manualshive.com logo in svg

Canon Colorado 1630, Operation Manual

Share
Download
Canon Colorado 1630 Operation Manual Download Page 40

Media specifications

MEDIA

Item

Specification

Roll width

From 279 mm (11 inch) to 1625 mm (64 inch)

Print margin

5.3 mm 

*

 (0.21 inch)

Roll weight

Up to 50 kg (110 lb.)

Roll diameter

Up to 220 mm (8.7 inch)

Media thickness

Up to 0.8 mm (0.03 inch)

Media input

Print side wound-in or out (licensed)
Double-sided printing possible (licensed)
Automatic and manual feed

Number of input rolls

2 (automatic roll-feeding and -switching depending on media used) (li-
censed)

Media take-up system Both loose and tight winding possible

*

 5.3 mm (0.21 inch) is the minimum print margin (no Automatic Advance correction). Print

margins are 8.9 mm (0.35 inch) with Normal Automatic Advance Correction and 17.5 mm (0.69
inch) with Enhanced Automatic Advance Correction. In print mode FLXfinish

+

 an additional strip

with a width of 15 mm (0.59 inch) is printed to keep the nozzles of the printheads in good
condition.

Media specifications

40

Chapter 4 - Handle the media

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands