Avaya P332G-ML User Manual Download Page 78

Page: 78 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guide

show time

Use the

show time

command to display the current stack time.

• show ppp incoming

timeout

Shows the amount of time PPP sessions
can remain idle before being
disconnected.

Page 85

• show ppp baud-rate

Shows the baud rate.

Page 85

• show ppp

configuration

Displays the ppp configuration.

Page 85

• show tftp upload/

download status

Shows the status of the TFTP upload/
download configuration per switch.

Page 86

• show tftp download

software status

Shows the status of the TFTP software
download of the Device Manager
software to the switch.

Page 86

• show web

aux-files-url

Shows the location (URL/directory) of
the P330 Device Manager Help files.

Page 87

• show intelligent-

multicast

Shows the status IP multicast filtering
application.

Page 87

• show intelligent-

multicast hardware
support

Shows whether the connected unit’s
hardware supports IP multicast filtering.

Page 88

• show security mode

Displays the status of the MAC security
feature (enabled/disabled).

Page 88

• show arp-tx-interval

Displays the keep-alive status.

Page 88

• show arp-aging-

interval

Displays the ARP table aging interval for
gateways’ entries.

Page 89

• show allowed

managers status

Displays the status of the allowed
managers feature (enabled/disabled) .

Page 89

• show allowed

managers table

Displays the IP addresses of the allowed
managers.

Page 89

• dir

Displays the file types that have been
downloaded to the module.

Page 90

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands