manualshive.com logo in svg

Avaya P332G-ML, User Manual

The Avaya P332G-ML is an advanced communication device designed to streamline your business operations. To easily get started, download the Quick Start Manual from our website for free. This informative manual offers step-by-step instructions for quick installation and setup, ensuring you make the most of this powerful product.

Share
Download
background image

Contents

ii

P332GT-ML User’s Guide

Route Redistribution  .................................................................... 12
Route Preferences  ........................................................................ 13
NetBios Rebroadcast ..................................................................... 13
Multinetting (Multiple Subnets per VLAN)  ................................. 13
Router Configuration File  ............................................................ 14

Avaya P334T-ML Standards Supported ................................................. 15

IEEE ............................................................................................. 15
IETF - Layer 2 ............................................................................... 15
IETF - Layer 3 ............................................................................... 15

Avaya P334T-ML Network Management............................................... 16

P334T-ML Device Manager (Embedded Web) ............................. 16
P334T-ML Command Line Interface (CLI)  .................................. 16
MSNM™ ...................................................................................... 16

Avaya P334T-ML Network Monitoring.................................................. 17

RMON I MIBs - RFC 1757  ........................................................... 17
SMON MIBs - RFC 2613  .............................................................. 17
Bridge MIB Groups - RFC 2674  ................................................... 17
Port Mirroring  .............................................................................. 17
SMON ........................................................................................... 17

Chapter 2

Avaya P334T-ML Front and Rear Panels ............................................... 19
Avaya P334T-ML Front Panel ................................................................ 19
Avaya P334T-ML Back Panel ................................................................. 23

BUPS-ML Input Connector  .......................................................... 24

Chapter 3

Applications............................................................................................  25
Application 1 .......................................................................................... 25
Application 2 .......................................................................................... 26
Application 3 .......................................................................................... 27

Chapter 4

Installation and Setup ............................................................................  29
Installing the X330STK-ML Stacking Sub-Module ................................ 29
Positioning..............................................................................................  30
Rack Mounting....................................................................................... 31
Connecting Stacked Switches................................................................. 32

To connect stacked switches:  ....................................................... 32

Powering On – P334T-ML Module AC .................................................. 35
Powering On – P334T-ML Module DC .................................................. 35
Configuring the Switch ..........................................................................  36

P334T-ML Default Settings  .......................................................... 36
Connecting the Cables  ................................................................. 38
Connecting the Console Cable  ..................................................... 39
Configuring the Terminal Serial Port Parameters  ........................ 39
Connecting a Modem to the Console Port  ................................... 39
Assigning P330’s IP Stack Address  ............................................... 40

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

Panio HW2250K User Manual preview
HW2250K
Brand: Panio Pages: 5
Holland HMS-412ARK Installation Instructions preview
HMS-412ARK
Brand: Holland Pages: 4
ALFAtron ALF- WUK3A Manual preview
ALF- WUK3A
Brand: ALFAtron Pages: 15
Microsonic zws-7/CD/QS Operating Instructions preview
zws-7/CD/QS
Brand: Microsonic Pages: 2
EtherWAN EX24000 User Manual preview
EX24000
Brand: EtherWAN Pages: 239
Uponor Smatrix Wave Plus Uahome Module R-167 Installation And Operation Manual preview
Smatrix Wave Plus Uahome Module R-167
Brand: Uponor Pages: 48
Linksys EG008W - Instant Gigabit Workgroup Switch User Manual preview
EG008W - Instant Gigabit Workgroup Switch
Brand: Linksys Pages: 27
Black Box LH8112A Installation And User Manual preview
LH8112A
Brand: Black Box Pages: 132
Brocade Communications Systems 7500 Extension Hardware Reference Manual preview
7500 Extension
Brand: Brocade Communications Systems Pages: 54
H3C PSR450-12A Manual preview
PSR450-12A
Brand: H3C Pages: 40
Raritan MCC8 User Manual preview
MCC8
Brand: Raritan Pages: 46
Weidmüller IE-SW-EL10-8GTPoE-2GESFP Hardware Installation Manual preview
IE-SW-EL10-8GTPoE-2GESFP
Brand: Weidmüller Pages: 2
S+S Regeltechnik PREMASREG 716x Series Operating Instructions, Mounting & Installation preview
PREMASREG 716x Series
Brand: S+S Regeltechnik Pages: 32
A-Neuvideo ANI-8X2MFS Instruction Manual preview
ANI-8X2MFS
Brand: A-Neuvideo Pages: 44
JABSCO 18680-0000 Manual preview
18680-0000
Brand: JABSCO Pages: 2
Extron electronics Matrix 50 Series User Manual preview
Matrix 50 Series
Brand: Extron electronics Pages: 74
Rosewill RC-407 User Manual preview
RC-407
Brand: Rosewill Pages: 5
Hitachi MS-1WL Specifications preview
MS-1WL
Brand: Hitachi Pages: 3

Brands by name

Popular brands

Load more brands