Avaya P332G-ML User Manual Download

Page: 185 / 254

Chapter 7

CLI – Layer 3

P334T-ML User’s Guide

167

Configure Mode

interface Command

Use the

interface

command to create and/or enter the Interface Configuration

Mode. Use the

form of this command to delete a specific IP interface.

The syntax for this command is:

[no] interface

Example:

Router-N(configure)# interface marketing

Note:

If you wish to define a name which includes spaces, you must enclose the

entire name in quotation marks, e.g. "new york".

ip default-gateway Command

Use the

ip default-gateway

command to define a default gateway (router).

The

form of this command removes the default gateway.

The syntax for this command is:

[no] ip default-gateway

<ip-address>[<cost>][<preference>]

Example:
To define the router at address 192.168.37.1 as the default gateway.

Router-N(configure)# ip default-gateway 192.168.37.1

interface name

String (up to 32 characters)

ip-address

The IP address of the router.

cost

The path cost. The default is 1

preference

Preference, either High or Low. Default is Low.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands