Avaya P332G-ML User Manual Download Page 119

Page: 119 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

101

• set port security

Enables MAC security on a range of
ports.

Page 122

• set cascading

Sets switch cascading fault-monitoring
mode.

Page 122

• set inband vlan

Sets the management VLAN ID.

Page 122

• set vlan

Creates VLANs.

Page 123

• set port flowcontrol

Sets the flow control mode of a port.

Page 123

• set port

autonegotiation-
flowcontrol-
advertisement

Sets the flowcontrol advertising
capabilities of a Gigabit port.

Page 125

• set trunk

Sets the tagging mode of a port.

Page 125

• set spantree

Enables/disables Spanning Tree
Protocol (STP).

Page 126

• set spantree priority

Sets the STP Bridge priority level.

Page 126

• set autopartition

Enables or disables autopartitioning for
switches in a stack.

Page 126

• set license

Enters a license number for the stack.

Page 127

• set ppp authentication

incoming

Defines the PPP authentication method.

Page 127

• set ppp incoming

timeout

Sets the time after which the system
automatically disconnects an idle PPP
incoming session.

Page 128

• set ppp baud-rate

Sets the baud rate used in PPP sessions.

Page 128

• set web

aux-files-url

Sets the location (URL/directory) of the
P330 Device Manager Help files.

Page 128

• set intelligent-multicast

Enables or disables the IP multicast
filtering application.

Page 129

• set intelligent-multicast

client-port-pruning
time

Sets the aging time for client ports.

Page 129

• set intelligent-multicast

router-port-pruning
time

Sets the aging time for router ports.

Page 129

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands