manualshive.com logo in svg

Avaya P332G-ML, User Manual

The Avaya P332G-ML is an advanced communication device designed to streamline your business operations. To easily get started, download the Quick Start Manual from our website for free. This informative manual offers step-by-step instructions for quick installation and setup, ensuring you make the most of this powerful product.

Share
Download
background image

Chapter 4

Installation and Setup

40

P334T-ML User’s Guide

5

Set the baud rate, ppp authentication, and ppp time out required to match your 
modem. These commands are described in the “Command Line Interface” 
chapter. 

6

At the prompt, type:

set interface ppp enable

The CLI responds with the following: 

Entering the Modem mode within 60 seconds...

Please check that the proprietary modem cable is plugged into the 

console port

7

Use the DB-25 to RJ-45 connector to plug the console cable to the modem’s DB-
25 connector. Plug the other end of the cable RJ-45 connector to the 
Avaya 

P334T

-ML console’s RJ-45 port.

8

The Avaya 

P334T

-ML enters modem mode. 

9

You can now dial into the switch from a remote station, and open a Telnet 
session to the PPP interface IP address.

Assigning P330’s IP Stack Address 

Note:  

All P334T-ML switches are shipped with the same default IP address. You 

must change the IP address of the master P330 switch in a stack in order to 
guarantee that the stack has its own unique IP address in the network.

Use the CLI to assign the P330 stack an IP address and net mask. The network 
management station can establish communications with the stack once this address 
had been assigned and the stack has been inserted into the network.
To assign a P330 IP stack address:
1

Establish a serial connection by connecting a terminal to the Master P330 switch 
of the stack.

2

When prompted for a Login Name, enter the default name

 root

3

When you are prompted for a password, enter the password

 root. 

You are 

now in Supervisor Level.

4

At the prompt, type:

set interface inband 

<vlan> <ip_address> <netmask>

Replace 

<vlan>

,

 <ip_address>

 and

 

<netmask>

 

with the VLAN, 

IP address and net mask of the stack.

5

Press Enter to save the IP address and net mask.

6

At the prompt, type 

reset

 and press Enter to reset the stack. After the Reset, 

log in again as described above.

7

At the prompt, type

 set ip route 

<dest> <gateway>

 

and replace 

<dest>

 

and 

<gateway>

 

with the destination and gateway IP addresses.

8

Press Enter to save the destination and gateway IP addresses.

At this point, you have assigned the P330 stack IP address and you can now 

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

Eaton RMQ-Titan M30 Series Instruction Leaflet preview
RMQ-Titan M30 Series
Brand: Eaton Pages: 4
IDEM SAFETY SWITCHES KLM-P2L Operating Instructions preview
KLM-P2L
Brand: IDEM SAFETY SWITCHES Pages: 2
Eaton Pow-R-Line SPX0361126 Maintenance Manual preview
Pow-R-Line SPX0361126
Brand: Eaton Pages: 584
Omron D4N-1A20R Datasheet preview
D4N-1A20R
Brand: Omron Pages: 16
Linksys ProConnect PS2KVM2 User Manual preview
ProConnect PS2KVM2
Brand: Linksys Pages: 17
Sams RSS-10v User Manual For Use And Maintenance preview
RSS-10v
Brand: Sams Pages: 14
Wavetronix Click 223 Installation preview
Click 223
Brand: Wavetronix Pages: 3
Manhattan 177290 User Manual preview
177290
Brand: Manhattan Pages: 4
Cypress CLUX-C61C Operation Manual preview
CLUX-C61C
Brand: Cypress Pages: 16
TRENDnet TEG-S41SX Specifications preview
TEG-S41SX
Brand: TRENDnet Pages: 2
Labgear HDS3K User Manual preview
HDS3K
Brand: Labgear Pages: 8
Madison M8000-C Installation And Maintenance preview
M8000-C
Brand: Madison Pages: 2
H3C S5500-28C-EI Installation Manual preview
S5500-28C-EI
Brand: H3C Pages: 96
NVision NV8288 User Manual preview
NV8288
Brand: NVision Pages: 86
ANTAIRA LMX-2602G-SFP Series Hardware Manual preview
LMX-2602G-SFP Series
Brand: ANTAIRA Pages: 19
Eagle E301DA Product Manual preview
E301DA
Brand: Eagle Pages: 2
NB CT-HDVD-4X14K-SW User Manual preview
CT-HDVD-4X14K-SW
Brand: NB Pages: 23
Net Optics iBYPASS 40G Quick Install Manual preview
iBYPASS 40G
Brand: Net Optics Pages: 20

Brands by name

Popular brands

Load more brands