Avaya P332G-ML User Manual Download Page 50 | Manualshive

Page: 50 / 254

background image

Chapter 4

Installation and Setup

32

P334T-ML User’s Guide

Connecting Stacked Switches

Note:

The two ends of the Octaplane cable terminate with different connectors. Each

connector can only be connected to its matching port.

The following cables are used to connect stacked switches:
•

Short Octaplane cable (X330SC) – ivory-colored, used to connect adjacent
switches (Catalog No. CB0223) or switches separated by a BUPS unit.

•

Long/Extra Long Octaplane cable (X330LC/X330L-LC) – ivory-colored, used to
connect switches from two different physical stacks, or switches separated by a
BUPS unit (Catalog No. CB0225/CB0270).

•

Redundant/Long Redundant Octaplane cable (X330RC/X330L-RC) – black,
used to connect the top and bottom switches of a stack (Catalog No. CB0222/
CB0269).

These are the same cables that are used with all the P330 switches.

To connect stacked switches:

Note:

When adding a module to an existing stack, first connect the stacking cables

and then power up the module.

1

Plug the light grey connector of the Short Octaplane cable into the port marked
“to upper unit” of the bottom P330 Family module.

2

Plug dark grey connector of same Short Octaplane cable to the port marked “to
lower unit” in the unit above. The connections are illustrated in Figure 4.3.

3

Repeat Steps 1 and 2 until you reach the top switch in the stack.

4

If you wish to implement stack redundancy, use the Redundant Cable to
connect the port marked “ to lower unit” on the bottom switch to the port
marked “to upper unit” on top switch of the stack.

5

Power up the added modules.

Caution:

Do not cross connect two P330 switches with two Octaplane (light-colored)

cables. If you wish to cross-connect for redundancy, use one light-colored Octaplane
cable and one black redundancy cable. Figure 4.2 shows an incorrect connection.

«
...
48
49
50
51
52
...
»

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

Brand: E-Trailer Pages: 8

Brand: H3C Pages: 55

Brand: H3C Pages: 111

Brand: H3C Pages: 34

Brand: H3C Pages: 47

Brand: H3C Pages: 8

Brand: H3C Pages: 47

Brand: H3C Pages: 4

S5560X-EI Series

Brand: H3C Pages: 63

S5560X-EI Series

Brand: H3C Pages: 89

Brand: H3C Pages: 3

S12500G-AF Series

Brand: H3C Pages: 86

Brand: H3C Pages: 168

Brand: H3C Pages: 56

Brand: H3C Pages: 19

Brand: H3C Pages: 4

Brand: H3C Pages: 36

TotalStorage 3534-F08

Brand: IBM Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands