Avaya P332G-ML User Manual Download

Page: 203 / 254

Chapter 7

CLI – Layer 3

P334T-ML User’s Guide

185

show ip ospf database Command

Use the

show ip ospf database

command to display lists of information

related to the OSPF database for a specific router.

The syntax for this command is:

show ip ospf database

[{asbr-summary|router|network|network-summary|external}]

Configure Mode

router ospf Command

Use the

router ospf

command to enable OSPF protocol on the system. The

form of this command disables it globally. The default is

disabled

The syntax for this command is:

[no] router ospf

asbr-summary

Displays information only about the autonomous
system boundary router summary LSAs. Optional.

external

Displays information only about the external LSAa.
Optional.

network

Displays information only about the network LSAa.
Optional.

network-summary

Displays information only about the network LSAa
summary. Optional

router

Displays information only about the router LSAs.
Optional.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands