Avaya P332G-ML User Manual Download

Page: 192 / 254

Chapter 7

CLI – Layer 3

174

P334T-ML User’s Guide

ip admin-state Command

Use the

ip admin-state

command to set the administrative state of an IP

interface. The default state is

The syntax for this command is:

ip admin-state

ip netbios-rebroadcast Command

Use the

ip netbios-rebroadcast

command to set NETBIOS rebroadcasts

mode on an interface. The

form of this command disables NETBIOS

rebroadcasts on an interface.

The syntax for this command is:

[no] ip netbios-rebroadcast

<mode>

The possible values of

mode

are:

Example:
To enable rebroadcasting of netbios packets received by and sent from the interface
“marketing”:

Router-N(config-if:marketing)# ip netbios-rebroadcast both

ip directed-broadcast Command

Use the

ip directed-broadcast

command to enable net-directed broadcast

forwarding. The

form of this command disables net-directed broadcasts on an

interface.

The syntax for this command is:

[no] ip directed-broadcast

up/down

Administrative state of the interface. The choices are

(active) or

down

(inactive).

both

Netbios packets received on the interface
rebrodcasted to other interfaces and netbios packets
received on other interfaces are rebroadcasted into
this interface.

disable

Netbios packets are not rebroadcasted into or out of
this interface.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands