Avaya P332G-ML User Manual Download Page 191

Page: 191 / 254

Chapter 7

CLI – Layer 3

P334T-ML User’s Guide

173

Interface Mode

ip address Command

Use the

ip address

command to assign an IP address and mask to an interface.

The syntax for this command is:

ip address

<ip-address> <mask> [<admin-state>]

Example:
To assign the IP address 192.168.22.33 with mask 255.255.255.0 to the interface
“marketing”:

Router-N(config-if:marketing)#

ip address 192.168.22.33

255.255.255.0

ip vlan/ip vlan name Commands

Use these

commands to specify the VLAN on which an IP interface resides. You

can specify either the VLAN ID using the

ip vlan

command or the VLAN name

using the

ip vlan name

command. The

form of the command restores the IP

interface to the default VLAN.

The syntax for this command is:

[no] ip vlan <vlan-id>

ip vlan name

<vlan-Name>

Example:
To specify VLAN developmental as the VLAN used by interface “products”:

Router-N(config-if:marketing)#

ip vlan name development

Note:

If you wish to define a name which includes spaces, you must enclose the

entire name in quotation marks, e.g. "new york".

ip address

The IP address assigned to the interface.

mask

Mask for the associated IP subnet

admin-state

The administration status – either Up or Down

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands