Avaya P332G-ML User Manual Download Page 126

Page: 126 / 254

Chapter 6

CLI – Layer 2

108

Avaya P334T-ML User’s Guide

The syntax for this command is:

set device-mode

<mode>

set interface

Use the

set interface

command to configure the management interface on the

Master agent of the stack.

The syntax for this command is:

set interface inband

Output Example:

P330-N# set interface inband 1 192.168.42.252 255.255.255.0

Interface inband IP address set.

You must reset the device in order for the change to take effect.

mode

Router | Layer2

inband

Interface name used for the management

vlan

The number of the VLAN to be used for management

ip_addr

IP address used for managing the stack

netmask

Subnet mask of the management interface

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands