Avaya P332G-ML User Manual Download Page 28 | Manualshive

Page: 28 / 254

background image

Chapter 1

Overview

10

P334T

-ML User’s Guide

Policy — Access Control

The P334T-ML supports Access Control policy. The P334T-ML uses policy lists
containing both Access Control rules and QoS rules. The policy lists are ordered by
rule indexing. Access Control rules define how the P334T-ML should handle routed
packets. There are three possible ways to handle such packets:
•

Forward the packet (Permit operation)

•

Discard the packet (Deny operation)

•

Discard the packet and notify the management station (Deny and Notify)

The P334T-ML can enforce Access Control policy on each routed packet, according
to the following criteria:
•

Matching the packet's source or destination IP address to the configured Access
Control policy.

•

Determine if the packet source or destination TCP/UDP port number falls
within a pre-defined range.

•

Using the ACK bit of the TCP header.

The P334T-ML access control rules are set-up using the Command Line Interface
and the Avaya MultiService Network Manager central policy management
application.

DHCP/BOOTP Relay

The P334T-ML supports the DHCP/BOOTP Relay Agent function. This is an
application that accepts DHCP/BOOTP requests that are broadcast on one VLAN
and sends them to a DHCP/BOOTP server that connects to another VLAN or a
server that may be located across one or more routers that would otherwise not get
the broadcast request. The relay agent handles the DHCP/BOOTP replies as well,
transmitting them to the client directly or as broadcast, according to a flag in the
reply message. Note that the same DHCP/BOOTP relay agent serves both the
BOOTP and DHCP protocols.
When there is more than one IP interface on a VLAN, the P334T-ML chooses one of
the IP addresses on this VLAN when relaying the DHCP/BOOTP request. The
DHCP/BOOTP server then uses this address to decide from which subnet the
address should be allocated.
When the DHCP/BOOTP server is configured to allocate addresses only from a
single subnet among the different subnets defined on the VLAN, you may need to
configure the P334T-ML with the relay address on that subnet so that the DHCP/
BOOTP server can accept the request.
DHCP/BOOTP Relay in P334T-ML is configurable per VLAN and allows for two
DHCP/BOOTP servers to be specified. In this case, it duplicates each request, and
sends it to both servers. This provides redundancy and prevents the failure of a
single server from blocking hosts from loading.
DHCP/BOOTP Relay in P334T-ML can be enabled or disabled.

«
...
26
27
28
29
30
...
»

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

D DGS-3048 DGS-3048

Brand: D-Link Pages: 3

Brand: Ruby Tech Pages: 2

Brand: WoMaster Pages: 2

Brand: Cabletron Systems Pages: 14

Brand: cable matters Pages: 8

Brand: H-Tronic Pages: 15

IDS-105FE Series

Brand: Perle Pages: 2

Brand: Black Box Pages: 57

Brand: INDO Pages: 3

Essentials EXP-SW-0401-H2

Brand: Wyrestorm Pages: 2

MMAC-Plus 9H421-12

Brand: Cabletron Systems Pages: 12

Brand: ADTRAN Pages: 5

Brand: Datacom Systems Pages: 55

Brand: Kramer Pages: 71

Brand: VICOR Pages: 31

Brand: MyQ Pages: 24

EPS-2XPB-SG-DPMS

Brand: Larson Electronics Pages: 2

Brand: SWR Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands