Avaya P332G-ML User Manual Download Page 106

Page: 106 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guide

show intelligent-multicast hardware-support

Use the

show intelligent-multicast hardware-support

command to

display the intelligent multicast hardware support configuration.

The syntax for this command is:

show intelligent-multicast hardware-support

Output Example:

P330-N> show intelligent-multicast hardware support

Intelligent-multicast HW configuration:

# Module Sub-Module Cascade

------- ---------- --------

1 Support IPMc Not Installed Support IPMc

show security mode

Use the

show security mode

command to display the status of the MAC

security feature at the stack level.

Note:

This command does not affect the P330-ML modules. It applies only to the

other P330 modules in the stack.

The syntax for this command is:

show security mode

Output Example:

P330-1(super)# show security mode

Switch-level security mode disabled

show arp-tx-interval

Use the

show arp-tx-interval

command to display the keep-alive frames

transmission interval.

The syntax for this command is:

show arp-tx-interval

Output Example:

P330-N> show arp-tx-interval

ARP tx interval is set to 5 seconds.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands