manualshive.com logo in svg

Avaya P332G-ML, User Manual

The Avaya P332G-ML is an advanced communication device designed to streamline your business operations. To easily get started, download the Quick Start Manual from our website for free. This informative manual offers step-by-step instructions for quick installation and setup, ensuring you make the most of this powerful product.

Share
Download
background image

Chapter 6

CLI – Layer 2

56

Avaya P334T-ML User’s Guide

session

Use the

 session 

command to open a session with a specific entity in a switch of 

the stack. For example, you can open a session with the Routing entity of a 
P332G-ML switch in the stack, or with an the X330 ATM sub-module entity plugged 
into a specific switch.

The syntax for this command is:

session

 [<mod_num> [switch|router|atm|mgp|wan]]

Note:  

Layer 2 commands are only available if you open a

 switch 

session with the 

Master switch.

Note:  

When you use the

 session 

command the security level stays the same.

terminal

Use the

 terminal width 

and

 terminal length 

commands to set the width 

and length of the terminal display in characters.

The syntax for this command is:

terminal 

{width|length} [<characters>]

mod_num

(optional) The switch number.
If you do not specify this parameter, you will 
get the default entity of the stack (Layer 2 
session to the Master)

switch|router|atm|mgp|wan

(optional) The entity to which you want to 
open a session.
If you do not specify this parameter, you will 
get the default entity of the specific module:

switch

 - Layer 2 entity of the switch (see 

Note below).

router

 - Routing entity.

atm

 - ATM entity.

mgp

 - Media Gateway Precessor.

wan

 - WAN access router entity.

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

D-Link DI-707 User Manual preview
DI-707
Brand: D-Link Pages: 36
D-Link DAP-1650 Quick Install Manual preview
DAP-1650
Brand: D-Link Pages: 16
D-Link DCH-G020 How-To preview
DCH-G020
Brand: D-Link Pages: 2
KELCO E30 Programming Instructions Manual preview
E30
Brand: KELCO Pages: 22
3Com SuperStack II Important Information preview
SuperStack II
Brand: 3Com Pages: 2
3Com CoreBuilder 5000 Quick Start And Reference preview
CoreBuilder 5000
Brand: 3Com Pages: 16
3Com CoreBuilder 9000 Quick Installation Manual preview
CoreBuilder 9000
Brand: 3Com Pages: 24
IDK MSD-804FD Series Command Manual preview
MSD-804FD Series
Brand: IDK Pages: 133
IDK MSD-72 Series User Manual preview
MSD-72 Series
Brand: IDK Pages: 150
IDK MSD-501 Command Reference Manual preview
MSD-501
Brand: IDK Pages: 101
IDK MSD-402 Command Reference Manual preview
MSD-402
Brand: IDK Pages: 85
IDK IMP-400UHD Command Reference Manual preview
IMP-400UHD
Brand: IDK Pages: 40
IDK FDX-32 User Manual preview
FDX-32
Brand: IDK Pages: 97
IDK FDX-S Series User Manual preview
FDX-S Series
Brand: IDK Pages: 117
IDK FDX-16 User Manual preview
FDX-16
Brand: IDK Pages: 77
Brightlink 16x16 Manual preview
16x16
Brand: Brightlink Pages: 33
H3C S1200 Series Compliance And Safety Manual preview
S1200 Series
Brand: H3C Pages: 90
Holland HMS-412ARK Installation Instructions preview
HMS-412ARK
Brand: Holland Pages: 4

Brands by name

Popular brands

Load more brands