Avaya P332G-ML User Manual Download Page 111

Page: 111 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

no hostname

Use the

no hostname

command to return the CLI prompt to its default.

The syntax for this command is:

no hostname

Note:

If this command is to be implemented on a switch other than the stack master,

a session should be opened to the relevant switch.

no rmon history

Use the

no rmon history

command to delete an existing RMON history entry.

The syntax for this command is:

no rmon history

no rmon alarm

Use the

no rmon alarm

command to delete an existing RMON alarm entry.

The syntax for this command is:

no rmon alarm

• copy tftp module-

config

Downloads a switch configuration file
(using TFTP).

Page 140

• copy tftp

EW_Archive

Downloads the Device Manager S/W
(Embedded Web Archive file), using
TFTP, into the device.

Page 141

• copy tftp

SW_image

Updates the software image and device
manager application of a designated
switch.

Page 141

• radius

authentication

Sets radius authentication parameters.

Page 142

1 The

clear

command corresponds to a group of commands and is

shown in a separate Table on Page 94.

2 The

set

command corresponds to a group of commands and is shown

in a separate Table on Page 99.

3 The

radius authentication

commands corresponds to a group

of commands listed on Page

142

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands