Avaya P332G-ML User Manual Download Page 125 | Manualshive

Page: 125 / 254

background image

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

107

set system location

Use the

set system location

command to set the mib2 system location MIB

variable.

The syntax for this command is:

set system location

[< location string>]

set system name

Use the

set system name

command to set mib2 system name MIB variable.

The syntax for this command is:

set system name

[<name string>]

set system contact

Use the

set system contact

command to set mib2 system contact MIB

variable.

The syntax for this command is:

set system contact

[<contact string>]

set device-mode

Use the

set device-mode

command to change the Basic Mode of Operation of

the P330-ML switches between Router and Layer 2 modes.

string

Location name. The location name is cleared if this field is left
blank. A string of 2 words or more must be type in quotation
marks – e.g. “Operations Floor”.

string

System name. The system name is cleared if this field is left blank.

A

string of 2 words or more must be type in quotation marks –
e.g. “Backbone Stack”.

string

Contact person. The contact person field is cleared if this field is
blank. A string of 2 words or more must be type in quotation
marks – e.g. “Yigdal Naouri”.

«
...
123
124
125
126
127
...
»

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

Brand: N-Tron Pages: 20

Brand: KELCO Pages: 22

Brand: Camozzi Pages: 2

Brand: Datavideo Pages: 58

Brand: Kramer Pages: 28

SET-2000 Oil/Sludge

Brand: Labkotec Pages: 15

AV Selector 310

Brand: Hama Pages: 21

BOCAHUB-16 Plus BEN220

Brand: Boca Pages: 56

Brand: Emos Pages: 44

Brand: Stahl Pages: 28

Brand: ATEN Pages: 15

Brand: Tripp Lite Pages: 9

Brand: WELLTECH Pages: 280

Brand: Lutron Electronics Pages: 2

Duramax LBZ DSP5

Brand: EFILive Pages: 21

Brand: ATEN Pages: 300

B-520-MTRX-230-6x4+2

Brand: Binary Pages: 32

Brand: ABB Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands