manualshive.com logo in svg

Avaya P332G-ML, User Manual

The Avaya P332G-ML is an advanced communication device designed to streamline your business operations. To easily get started, download the Quick Start Manual from our website for free. This informative manual offers step-by-step instructions for quick installation and setup, ensuring you make the most of this powerful product.

Share
Download
background image

Chapter 1

Overview

14

P334T

-ML User’s Guide

For example, if there are two interfaces over the same VLAN and you configure 
DHCP server on one interface it will be used also for the second interface over the 
same VLAN. This behavior might be less expected and in some cases wrong.
In order to prevent misconfiguration and unexpected results, the P334T-ML 
prevents configuration of VLAN-oriented commands on an interface unless the user 
explicitly requested to using the new "enable vlan commands" CLI command.
Configuration of "enable vlan commands" on an interface overrides this 
configuration on other interfaces that belong on the same VLAN.
This ensures that VLAN-oriented commands can be configured from one interface 
only.
In case there is only one interface over a VLAN, then VLAN oriented commands for 
this VLAN can be configured through the single interface without the need to issue 
the "enable vlan command" command.

Note:  

1. VLAN-oriented commands that were configured affect the VLAN of the interface 
that was used at the time the command was issued.
2. If the interface is moved to another VLAN (using the "ip vlan command") VLAN 
oriented configuration still relates to the original VLAN.

Router Configuration File

The Configuration File feature allows the user to read the P334T-ML routing 
configuration parameters and save them to a file on the station. The routing 
configuration commands in the file are in CLI format. The user can edit the file (if 
required) and re-configure the P334T-ML by downloading the configuration file. 
Although the file can be edited, it is recommended to keep changes to the file to a 
minimum. The recommended configuration method is using MSNM P330 Device 
Manager and/or the CLI. Changes to the configuration file should be limited to 
those required to customize a configuration file from one router to suit another.

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

N-Tron 100 Series User Manual & Installation Manual preview
100 Series
Brand: N-Tron Pages: 20
Campbell Hausfeld CW301300AJ Operating Instructions And Parts Manual preview
CW301300AJ
Brand: Campbell Hausfeld Pages: 12
FELA SWITCH CASAMBI Operation And Installation Manual preview
SWITCH CASAMBI
Brand: FELA Pages: 13
Lantronix SM12XPA Install Manual preview
SM12XPA
Brand: Lantronix Pages: 40
Lantronix SM12XPA Quick Start Manual preview
SM12XPA
Brand: Lantronix Pages: 2
Lantronix SISTP1040-551-LRT Quick Start Manual preview
SISTP1040-551-LRT
Brand: Lantronix Pages: 2
Lantronix SM24TBT2DPA Quick Start Manual preview
SM24TBT2DPA
Brand: Lantronix Pages: 2
Lantronix SISPM1040-3 L Series Quick Start Manual preview
SISPM1040-3 L Series
Brand: Lantronix Pages: 2
Lantronix SISPM1040 L3 Series Install Manual preview
SISPM1040 L3 Series
Brand: Lantronix Pages: 36
Lantronix SecureLinx Spider Quick Start Manual preview
SecureLinx Spider
Brand: Lantronix Pages: 18
Lantronix LSS2200-8P User Manual preview
LSS2200-8P
Brand: Lantronix Pages: 8
Lantronix EDS4100 Quick Start Manual preview
EDS4100
Brand: Lantronix Pages: 6
Lantronix SISPM1040-582-LRT Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 272
Lantronix Xpress-Pro SW 52000 Supplementary Manual preview
Xpress-Pro SW 52000
Brand: Lantronix Pages: 8
A-Neuvideo ANI-H-KIT Instruction Manual preview
ANI-H-KIT
Brand: A-Neuvideo Pages: 28
GarrettCom DS60s Installation And User Manual preview
DS60s
Brand: GarrettCom Pages: 39
Articona 386428 Quick Installation Manual preview
386428
Brand: Articona Pages: 2
ETS SM8-RC Instructions preview
SM8-RC
Brand: ETS Pages: 2

Brands by name

Popular brands

Load more brands