Avaya P332G-ML User Manual Download Page 109

Page: 109 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

Output Fields:

Note:

If the

N/A

is displayed for the EW_Archive file, this means that the Device

Manager S/W is not loaded correctly. Download the Device Manager S/W again.

Field

Description

The switch number

file

There are several files loaded into the switch’s memory:
• module-config – file which contains the configuration

settings made to this switch

• stack-config – file which contains the configuration settings

made at the stack level (for example IP address of the stack)

• EW_Archive – file which contains the Device Manager

(Embedded Web) software

ver num

S/W Version number – relevant only for the Device
Management S/W

file type

There are several file types:
• Running Conf – the configuration currently in use and the

startup configuration in the P330-ML, P333R and P333R-LB.

• SW Web Image – Device Manager S/W archive file

file location

Type of internal memory into which the file is loaded

file description

Description of the file

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands