Avaya P332G-ML User Manual Download Page 160

Page: 160 / 254

Chapter 6

CLI – Layer 2

142

Avaya P334T-ML User’s Guide

<mod_num>

Example:

P330-N# copy tftp SW_image c:\p330\p330web101 EW_archive

c:\p330\p330web201 192.168.49.10 5

Radius Commands

The following radius commands are accessible from Privileged mode.

image-file

Common name for the files that contain the Software
Image and Embedded Web archive (full path)

filename

Embedded Web Manager image file name (full path)

The ip address of the TFTP server

mod_num

Target switch number

• set radius

authentication secret

Enables secret authentication for the
Avaya P330 unit.

Page 143

• set radius

authentication
server

Sets a primary or secondary RADIUS
server IP address.

Page 143

• clear radius

authentication
server

Removes a primary or secondary
RADIUS authentication server.

Page 143

• set radius

authentication retry-
time

Sets the time to wait before re-sending
an access request.

Page 144

• set radius

authentication retry-
number

Sets the number of times an access
request is sent when there is no
response.

Page 144

• set radius

authentication udp-
port

Sets the RFC 2138 approved UDP port
number.

Page 144

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands