Avaya P332G-ML User Manual Download Page 121

Page: 121 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

103

Output Example:
To disable the automatic disconnection of idle sessions:

P330-N# set logout 0

Sessions will not be automatically logged out.

set timezone

Use the

set timezone

command to assign a timezone name and set the time

difference of your P330 relative to the Coordinated Universal Time (UTC/GMT).
The minutes parameter can only be set to 30.

The syntax for this command is:

set timezone

<zone_name> <hours | hours:min>

Output Example:

set timezone GMT -3:30

Timezone set to 'GMT', offset from UTC is -3:30 hours

Note:

If you wish to define a name which includes spaces, you must enclose the

entire name in quotation marks, e.g. "new york".

set time protocol

Use the set time protocol command to set the protocol for use in the system as either
SNTP protocol or TIME protocol.

The syntax for this command is:

set time protocol

[sntp-protocol|time-protocol]

Output Example:

P330-N# set time protocol sntp-protocol

The protocol has been set to SNTP protocol

Output Example:

P330-N# set time protocol time-protocol

The protocol has been set to TIME protocol

set time server

The

set time server

command is used to set the TIME server address.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands