manualshive.com logo in svg

Avaya P332G-ML, User Manual

The Avaya P332G-ML is an advanced communication device designed to streamline your business operations. To easily get started, download the Quick Start Manual from our website for free. This informative manual offers step-by-step instructions for quick installation and setup, ensuring you make the most of this powerful product.

Share
Download
background image

Chapter 7

CLI – Layer 3

180

P334T-ML User’s Guide

ip rip send-receive Command

Use the

 ip rip send-receive 

command to set the RIP Send and Receive mode 

on an interface. The default state is 

talk-listen

.

The syntax for this command is:

ip rip send-receive 

<mode>[<default route metric>]

Example:
To set the RIP Send and Receive mode on the interface “marketing” to be listen-only:

Router-N(config-if:marketing)# 

ip rip send-receive talk listen

ip rip default-route-mode Command

Use the

 ip rip default-route-mode 

command to enable learning of the 

default route received by the RIP protocol. The default state is talk-listen.

The syntax for this command is:

ip rip default-route-mode

 <mode>

The possible default route modes on an interface are:

mode 

talk-listen - 

Set RIP to receive and transmit 

updates on the interface.

talkdefault-listen - 

Set RIP to receive 

updates on the interface and send only a default 
route.

default route metric

Integer value 

talk-listen

Set RIP to send and receive default route updates on 
the interface.

talk-only

Set RIP to send but not receive default route updates 
on the interface.

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

S&C 2000 series Instructions For Field Assembly And Installation preview
2000 series
Brand: S&C Pages: 26
S&C 2000 series Installation And Operation Manual preview
2000 series
Brand: S&C Pages: 37
S&C 2000 series Installation Manual preview
2000 series
Brand: S&C Pages: 28
Kathrein EXR 221 Quick Start Manual preview
EXR 221
Brand: Kathrein Pages: 8
Nayar Systems Switch Manual preview
Switch
Brand: Nayar Systems Pages: 21
Kathrein EXD 1532 User Manual preview
EXD 1532
Brand: Kathrein Pages: 24
Kasia Switch Installation Manual preview
Switch
Brand: Kasia Pages: 5
Qlogic SANbox 5802V Installation Manual preview
SANbox 5802V
Brand: Qlogic Pages: 124
Qlogic SANbox 5800V Series User Manual preview
SANbox 5800V Series
Brand: Qlogic Pages: 158
Qlogic SANbox 5602 User Manual preview
SANbox 5602
Brand: Qlogic Pages: 324
Qlogic SANbox 5600 Series Quick Start Manual preview
SANbox 5600 Series
Brand: Qlogic Pages: 8
Qlogic SANbox 5600 Series Supplementary Manual preview
SANbox 5600 Series
Brand: Qlogic Pages: 10
Qlogic SANbox 5200 Series Supplementary Manual preview
SANbox 5200 Series
Brand: Qlogic Pages: 2
Qlogic SANbox 3810 Installation Manual preview
SANbox 3810
Brand: Qlogic Pages: 92
Qlogic SANbox 3810 User Manual preview
SANbox 3810
Brand: Qlogic Pages: 142
Qlogic SANbox 3050 Specifications preview
SANbox 3050
Brand: Qlogic Pages: 2
Qlogic SANbox 1400 Series Specifications preview
SANbox 1400 Series
Brand: Qlogic Pages: 2
Qlogic QLogic Fibre Channel Switch Quick Start Manual preview
QLogic Fibre Channel Switch
Brand: Qlogic Pages: 8

Brands by name

Popular brands

Load more brands