Avaya P332G-ML User Manual Download Page 219

Page: 219 / 254

Chapter 7

CLI – Layer 3

P334T-ML User’s Guide

201

Example:
To add station 192.168.37.46 as a bootp/dhcp server to handle bootp/dhcp requests
arriving at the interface “marketing”:

Router-N(config-if:marketing)# ip bootp-dhcp server

192.168.37.46

ip bootp-dhcp network Command

Use the

ip bootp-dhcp network

command to select the network from which

the bootp/dhcp server shall allocate an address. This command is required only
when there are multiple interfaces over the VLAN. The

form of this command

restores to the default.

The syntax for this command is:

[no] ip bootp-dhcp network

<ip-address>

Example:
To select the network 192.168.169.0 as the network from which an address shall be
allocated for bootp/dhcp requests:

Router-N(config-if:marketing)# ip bootp-dhcp network

192.168.169.0

ip-address

The IP address of the network.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands