Avaya P332G-ML User Manual Download

Page: 226 / 254

Chapter 7

CLI – Layer 3

208

P334T-ML User’s Guide

Example:

Router-N>ip access-list-copy 100 101

ip simulate Command

Use the

ip simulate

command to check the policy for a simulated packet. The

command contains the addressed list number, and the packet parameters.

The syntax for this command is:

ip simulate

<access-list-number> [<priority>] [<dscp-

value>]<source> <destination> [<protocol> [<source port>

<destination port> [<established>]]]

Example:

Router-N>ip simulate 100 192.67.85.12 193.76.54.25

validate-group Command

Use the

validate-group

command to verify that all the rules in a priority list

are valid.
If there is a configuration problem with a specific rule, or with a number of rules,
detailed error messages will be given.

The syntax for this command is:

validate-group

<policy-list-number>[quiet]

quiet - does not display error messages

access-list-number

integer (100..199)

priority

fwd0 | fwd1 | .. | fwd7

dspc value

dscp0 | dscp1 | .. | dscp63

source

source ip address

destination

destination ip address

protocol

ip | tcp | udp | integer (1..255)

source port

integer (1..65535)

destination port

integer (1..65535)

established

value of TCP established bit

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands