Avaya P332G-ML User Manual Download Page 65 | Manualshive

Page: 65 / 254

background image

P334T-ML User’s Guide

47

Chapter 5

CLI – Architecture, Access & Conventions

This chapter describes the P334T-ML CLI architecture and conventions, and
provides instructions for accessing the P334T-ML for configuration purposes.
The configuration procedure involves establishing a Telnet session or a serial
connection and then using the P330’s internal CLI. The CLI is command-line driven
and does not have any menus. To activate a configuration option, you must type the
desired command at the prompt and press Enter. You can also configure your
P334T-ML using the P330 Manager with its graphical user interface. For details, see
the P330 Device Manager Appendix and the Avaya MultiService Network Manager
(MSNM) P330 Device Manager User Guide on the Documentation and Utilities CD.

CLI Architecture

The P330 stack supports both Layer 2 switching and Layer 3 switching.
The P334T-ML CLI includes two CLI entities to support this functionality.

•

The Switch CLI entity is used to manage Layer 2 switching of the entire stack.
The Switch CLI entity is identical to the CLI of a P330 Layer 2 modules.
CLI commands for managing Layer 2 switching are described in Chapter 6.

•

The Router CLI entity is used to manage Layer 3 switching of a single module.
The Router CLI entity exists in P334T-ML Layer 3 modules and supports
different sets of commands depending on the device mode of the module.

Router mode commands are described in Chapter 8.

If the P334T-ML module is the Master of the stack, then the Switch CLI entity and
the Router CLI entity co-exist on the same module.
To switch between the entities, use the

session

command. Refer to P330

Sessions.
Configuration of the

password

commands and

community

commands in one

entity is automatically attributed to the other entity in the stack.
Initial access to the stack can be established via a serial connection or a Telnet
connection to any one of the entities.

«
...
63
64
65
66
67
...
»

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

Brand: Gefen Pages: 11

xStack DES-3500 Series

Brand: D-Link Pages: 260

DXS-3600 Series

Brand: D-Link Pages: 48

DXS-3400 SERIES

Brand: D-Link Pages: 3

Web Smart Switch DGS-1210-16

Brand: D-Link Pages: 71

Brand: D-Link Pages: 3

Brand: D-Link Pages: 56

xStack DES-3800 Series

Brand: D-Link Pages: 326

xStack DES-3526

Brand: D-Link Pages: 222

Brand: D-Link Pages: 2

DXS-1210 Series

Brand: D-Link Pages: 20

Brand: NETGEAR Pages: 15

Brand: Idem Pages: 2

Brand: Hama Pages: 14

Super Speed USB 3.0 Hub

Brand: Hama Pages: 14

Brand: Hama Pages: 12

Brand: Hama Pages: 14

Premium Silver USB 2.0 Hub 1:4

Brand: Hama Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands