Avaya P332G-ML User Manual Download Page 174

Page: 174 / 254

Chapter 7

CLI – Layer 3

156

P334T-ML User’s Guide

copy startup-config tftp Command

Use the

copy startup-config tftp

command to copy the P332-ML

configuration from the NVRAM Startup Configuration to the TFTP file.

The syntax for this command is:

copy startup-config tftp

Example:

Router-N> copy startup-config tftp c:\p332\router1.cfg

192.168.49.10

erase startup-config Command

The

erase startup-config

command erases the P332-ML module NVRAM

configuration.

The syntax for this command is:

erase startup-config

reset Command

The

reset

command resets the P332-NL module. This command resets only the

specific module. If the module is the master of the stack the entire stack is reset.
If you want to keep changes you made to the current running configuration use the

copy running-config startup-config

command first.

The syntax for this command is:

reset

filename

file name (full path)

The ip address of the host

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands