Avaya P332G-ML User Manual Download Page 170 | Manualshive

Page: 170 / 254

background image

Chapter 7

CLI – Layer 3

152

P334T-ML User’s Guide

User /Privileged Command Mode

hostname Command

Use the

hostname

command to change the system prompt used for the router.

This command does not change the system prompt of the stack. To change the
system prompt of the stack, use the host name command in the switch CLI tree.

The syntax for this command is:

[no] hostname

[<hostname_string>]

Note:

If you wish to define a name which includes spaces, you must enclose the

entire name in quotation marks, e.g. "new york".

show device-mode Command

Use the

show device-mode

command to show the P332-ML operating mode

you are currently in. Possible modes are Router, or Switch.

The syntax for this command is:

show device-mode

show copy status Command

Use the

show copy status

command to show the status of the local

configuration copy operation.

The syntax for this command is:

show copy status

show tftp download status Command

Use the

show tftp download status

command to view the status of the tftp

download operation.

The syntax for this command is:

show tftp download status

hostname_string

The string to be used as the hostname
(up to 20 characters).

«
...
168
169
170
171
172
...
»

Summary of Contents for P332G-ML































































































































































































































































Reviews:

No comments

Related manuals for P332G-ML

Brand: NEC Pages: 168

Brand: A SYSTEMS Pages: 16

Brand: GarrettCom Pages: 24

Brand: Radial Engineering Pages: 8

Brand: Radial Engineering Pages: 2

Brand: BeeSecure Pages: 35

Brand: Kramer Pages: 8

AVS-OP-1616-340

Brand: AMX Pages: 1

Brand: INFLUX MEASUREMENTS Pages: 6

Brand: BERNSTEIN Pages: 3

EtherDevice EDS-4009 Series

Brand: Moxa Technologies Pages: 18

Brand: TP-Link Pages: 2

Allen-Bradley 194U Series

Brand: Rockwell Automation Pages: 2

Brand: Alloy Pages: 33

Brand: Black Box Pages: 3

Brand: Hama Pages: 14

Brand: Kramer Pages: 33

Giga-AcessEtherLinx-II

Brand: IMC Networks Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands