Avaya P332G-ML User Manual Download Page 196

Page: 196 / 254

Chapter 7

CLI – Layer 3

178

P334T-ML User’s Guide

Router-RIP Mode

redistribute Command

Use the

redistribute

command to redistribute routing information from other

protocols into RIP. The

form of this command disables redistribution by RIP.

The default is

disabled

The syntax for this command is:

[no] redistribute

Example:

Router-N(configure router:rip)# redistribute ospf

network Command

Use the

network

command to specify a list of networks on which the RIP is

running. The

form of this command removes an entry.

The syntax for this command is:

[no] network

<ip-address> [<wildcard-mask>]

Example:
To specify that RIP will be used on all interfaces connected to the network
192.168.37.0:

Router-N(configure router:rip)#

network 192.168.37.0

protocol

Either Static or OSPF

ip addr

The IP address of the network of directly connected networks

wildcard-mask

Wildcard mask address. Exists for compatibility with P550.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands