Avaya P332G-ML User Manual Download Page 124

Page: 124 / 254

Chapter 6

CLI – Layer 2

106

Avaya P334T-ML User’s Guide

Output Example:
To enable all traps to a specific manager:

P330-N# set snmp trap 192.168.173.42 enable all

All SNMP traps enabled.

Output Example:
To disable SNMP config traps to a specific manager:

P330-N# set snmp trap 192.168.173.42 disable config

SNMP config traps disabled.

Output Example:
To add an entry in the SNMP trap receiver table with default:

P330-N# set snmp trap 192.168.173.42

SNMP trap receiver added.

set snmp trap auth

Use the

set snmp trap auth

commands to enable/disable the sending of

SNMP traps upon SNMP authentication failure.

The syntax for this command is:

set snmp trap

{enable|disable}

auth

Output Example:

P330-N# set snmp trap enable auth

Authentication trap enabled

set snmp retries

Use the

set snmp retries

command to set the number of retries initiated by

the Device Manager application when it tries to send SNMP messages to the device.

The syntax for this command is:

set snmp retries

set snmp timeout

Use the

set snmp timeout

command to set the SNMP timeout in seconds. This

command is useful for access using the Device Manager.

The syntax for this command is:

set snmp timeout

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands