Avaya P332G-ML User Manual Download Page 94

Page: 94 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guide

Output Example:

P330-N> show trunk 1/5

Port Mode Binding mode Native vlan Vlans allowed on trunk

------ ----- -------------- ----------- ----------------------

1/5 off statically bound 1 1

Output Fields:

show vlan

Use the

show vlan

command to display the VLANs configured in the stack/

switch.

The syntax for this command is:

show vlan

Output Example:

P330-N> show vlan

VLAN ID Vlan-name

------- --------------------------------

1 v1

5 V5

10 V10

15 V15

20 V20

25 V25

Field

Description

Port

Switch and port number(s)

Mode

Tag status of the port (dot1q - dot1Q tagging mode,
off - clear mode).

Binding mode

Binding mode of the port

Native VLAN

Number of the Port VLAN ID (the VLAN to which received
untagged traffic will be assigned).

VLANs allowed
on trunk

Range of VLAN values allowed on the port.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands