Avaya P332G-ML User Manual Download Page 190

Page: 190 / 254

Chapter 7

CLI – Layer 3

172

P334T-ML User’s Guide

ip netmask-format Command

Use the

ip netmask-format

command to specify the format of netmasks in the

show

command output. The

form of this command restores to the default,

which is a dotted decimal format.

The syntax for this command is:

[no] ip netmask-format

<mask-format>

The possible mask formats are:

Example:
To display netmasks in bitcount format:

Router-N(configure)#

ip netmask-format bitcount

bitcount

Addresses are followed by a slash and the total number of bits
in the netmask. For example 17

decimal

The network masks are in dotted decimal notation. For
example, 255.255.255.0.

hexadecimal

The network masks are in hexadecimal format as indicated by
the leading 0X. For example, 0XFFFFFF00.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands