Avaya P332G-ML User Manual Download

Page: 197 / 254

Chapter 7

CLI – Layer 3

P334T-ML User’s Guide

179

Interface Mode

ip rip rip-version Command

Use the

ip rip rip-version

command to specify the RIP version running on

the interface basis.

The syntax for this command is:

ip rip rip-version

[1][2]

The possible versions of the RIP packets received and sent on an interface are:

Example:
To specify that RIP version 2 should be running on the basis of the interface
“marketing”:

Router-N(config-if:marketing)# ip rip rip version 2

default-metric Command

Use the

default-metric

command to set the interface RIP route metric. The

form of this command restores the default. The default metric is

The syntax for this command is:

[no] default-metric

Example:
To set the default RIP metric value. The range is 0 to 15:

Router(config-if:marketing)# default-metric 10

[1]

RIP Version 1 packets

[2]

RIP Version 2 packets.

number

The interface RIP route metric value. The range is 0 to 15.

Summary of Contents for P332G-ML































































































































































































































































Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands

Avaya P332G-ML, User Manual

Search results

Summary of Contents for P332G-ML

Reviews:

Related manuals for P332G-ML

Brands by name

Popular brands