95
turns off. When the unit turns off, press the
▼
/
▲
Navigation Button [oval 16]
to move the cursor
next to:
YES
. Press the
Set Button [oval 18].
This will ‘save’ this code group for ON/OFF control
of the lights.
If no IR ON/OFF commands were found, see
Automatic
and
Learn
, below.
If no further programming is required, press the
AVR Button [oval 5]
on the AVR21ENR1 remote
and then the
Exit Button [oval 17]
to return to normal operation mode.
To continue in setup, press the
▼
Navigation Button [oval 16]
to move the cursor next to:
BACK
TO LGT CODE PROG
. Press the
Set Button [oval 18]
. Press the
▼
Navigation Button [oval
16]
again to move the cursor next to:
BACK TO LGT CNTL SETUP
. Press the
Set Button [oval
18]
. The
LIGHTING CONTROL SETUP
screen will appear.
To program
TV/PROJECTOR ON/OFF
,
SCREEN ON/OFF
, press the
▼
/
▲
Navigation Button
[oval 16]
to move the cursor next to:
BACK TO REM CNTL SETUP
. Press the
Set Button [oval
18]
. See the TV/Projector and Screen sections.
Lighting Program Code (Automatic)
If ON/OFF codes could not be found by Brand in the Manual Mode, try searching by source type
in the Automatic mode.
In the
LIGHTING CODE PROGRAM
screen, press the
▼
/
▲
Navigation Button [oval 16]
to move
the cursor next to:
AUTOMATIC
. Press the
Set Button [oval 18]
. The
LIGHTING AUTO
PROGRAM
screen will appear.
The
SOURCE
will be fixed as selected (
LIGHTING
). Press the
▼
Navigation Button [oval 16]
to
move the cursor next to:
TRY CODES
. Repeatedly press the
◄
or
►
Navigation Button
[oval 16]
to test all selected device type commands until the unit turns off. When the unit turns off, press
the
▼
Navigation Button [oval 16]
to move the cursor next to:
YES
. Press the
Set Button [oval
18]
to ‘save’ the code group. This will set this code group for ON/OFF control of the Lights.
If no further programming is required, press the
AVR Button [oval 5]
on the AVR21ENR1 remote
and then the
Exit Button [oval 17]
to return to normal operation mode.
To continue in setup, press the
▼
Navigation Button [oval 16]
to move the cursor next to:
BACK
TO LGT CODE PROG
. Press the
Set Button [oval 18]
. Press the
▼
Navigation Button [oval
16]
again to move the cursor next to:
BACK TO LGT CNTL SETUP
. Press the
Set Button [oval
18]
. The
LIGHTING CONTROL SETUP
screen will appear.
To program
TV/PROJECTOR ON/OFF
,
SCREEN ON/OFF
,
CURTAIN OPEN/CLOSE
, press the
▼
/
▲
Navigation Button [oval 16]
to move the cursor next to:
BACK TO REM CNTL SETUP
.
Press the
Set Button [oval 18]
. See the TV/Projector, Screen and Curtain sections.
If a particular brand or functional code from a source type cannot be found in the on-board IR
code Library, IR commands for Lights ON/OFF, or a particular scene, can be taught to the AVR
from the original equipment remote. To teach Lighting ON/OFF or scene codes to the AVR,
proceed to section:
Learn Code
.
Lighting Program (Learn Code)
To teach the AVR21EN Lighting ON/OFF codes, in the
LIGHTING CONTROL SETUP
screen,
press the
▼
Navigation Button [oval 16]
to move the cursor next to:
LEARN CODE
. Press the
Set Button [oval 18]
. The
LIGHTING CODE LEARN
screen will appear.
With the cursor positioned next to
USING THE
◄
/
►
KEYS
line, press the
Set Button [oval 18]
.
The message:
USING THE
◄
/
►
KEYS SELECT FUNCTION TO BE PROG
will start to flash,
Summary of Contents for AVR21EN
