94
panel; or press the
ON Button [oval 2]
on the AVR21ENR1 remote. The AVR should turn ON
and the screen should drop.
To test OFF, either: press the
Standby/ON Button [square 2]
on the AVR front panel; or: press
the
OFF Button
on the AVR21ENR1 remote. The AVR should turn OFF and the screen should
retract.
To test the SCREEN UP/DOWN commands with MANUAL VIA REMOTE, turn the AVR OFF and
manually raise the screen. Turn the AVR ON by pressing the
Standby/ON Button [square 2]
on
the AVR front panel or press the
ON Button [oval 2]
on the remote. (The AVR should be on, but
the screen should still be retracted.) Press the
Trigger Button [oval 50]
on the remote. The
screen should drop. Press the
Trigger Button [oval 50]
again and the screen should retract.
Exit Setup
If no further programming is required, press the
AVR Button [oval 5]
on the AVR21ENR1 remote
and then the
Exit Button [oval 17]
to return to normal operation mode.
LIGHTING CONTROL
To control the Main Room lighting with the AVR turn on/turn off functions, press the
Menu Button
[oval 44]
on the remote to bring the
MAIN MENU
to the screen. Press the
▼
/
▲
Navigation
Button [oval 16]
so that the cursor is pointed to the
REMOTE CONTROL SETUP
line. Press the
Set Button [oval 18]
. The
REMOTE CNTL SETUP 1
screen will appear. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to
GO TO REMOTE CNTL 2
. Press
the
Set Button [oval 18]
. The
REMOTE CNTL SETUP 2
screen will appear. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
LIGHTING CONTROL
line. Press
the
Set Button [oval 18]
. The
LIGHTING CONTROL SETUP
screen will appear.
Carrier
With the cursor positioned next to
CARRIER
, press the
◄
/
►
Navigation Button [oval 16]
to
select the proper setting. NOTE: Most IR remotes used with common source components will
have a carrier, so
YES
should be selected as a first test. Some Cable Box remotes do not use a
carrier, so if a code setting doesn’t work, try changing this setting.
Invert Code
Press the
▼
/
▲
Navigation Button [oval 16]
to move the cursor next to:
INVERT CODE
. Press
the
◄
/
►
Navigation Button [oval 16]
to select
YES/NO
. Most devices will be set to
NO
. Certain
devices, (Sony S-Link, Harman Kardon Remote Control IN) will require a
YES
setting. Try
changing this setting if a specific code selection does not work for a given device.
Program Code
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
PROGRAM CODE
line. Press the
Set Button [oval 18]
. The
LIGHTING CODE PROGRAM
screen will appear.
Lighting Program Code (Manual)
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
MANUAL
line.
Press the
Set Button
. The
LIGHTING MANUAL PROG
screen will appear.
SOURCE TYPE
will be
fixed as selected (
LIGHTING
).
Press the
▼
/
▲
Navigation Button
to move the cursor next to:
BRAND
. Press the
◄
/
►
Navigation Button [oval 16]
to select the appropriate brand.
Press the
▼
/
▲
Navigation Button [oval 16]
to move the cursor next to:
TRY CODES
. With the
AVR21ENR1 Main Room Remote pointing toward the AVR front panel, starting with 1, slowly
press the numeric buttons through the range indicated on screen, until the unit being configured
Summary of Contents for AVR21EN
