97
To configure the AVR21EN
Trigger Out
Jack [circle 38]
to control Lighting when the Main Room
is turned ON:
Press the
Menu Button [oval 44]
on the remote to bring the
MAIN MENU
to the screen. Press
the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
REMOTE CONTROL
SETUP
line. Press the
Set Button [oval 18]
. The
REMOTE CNTL SETUP 1
screen will appear.
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to
GO TO REMOTE
CNTL 2
. Press the
Set Button [oval 18]
. The
REMOTE CNTL SETUP 2
screen will appear.
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
ASSIGN
TRIGGER OUT
line. Press the
◄
/
►
Navigation Button [oval 16]
until
LGHT
appears. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to
LIGHTING CONTROL
. Press
the
Set Button [oval 18]
. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is
pointed to the
CONTROL
line. Press the
◄
/
►
Navigation Button [oval 16]
to select the preferred
mode. Press
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
BACK TO
REM CNTL SETUP
line. Press the
Set Button [oval 18]
.
To test the Lighting ON/OFF commands with AVR ON/OFF, turn the AVR OFF and manually turn
the lights OFF. To test ON, either: press the
Standby/ON Button [square 2]
on the AVR front
panel; or press the
ON Button [oval 2]
on the AVR21ENR1 remote. The AVR should turn ON
and the lights should turn ON or change scenes.
To test OFF, either: press the
Standby/ON Button [square 2]
on the AVR front panel; or: press
the
OFF Button [oval 1]
on the AVR21ENR1 remote. The AVR should turn OFF and the lights
should turn OFF or change scenes.
To test the LIGHTING commands with MANUAL VIA REMOTE, turn the AVR OFF and manually
turn the lights OFF. Turn the AVR ON by pressing the
Standby/ON Button [square 2]
on the
AVR front panel or press the
ON Button [oval 2]
on the remote. (The AVR should be on, but the
Lights should still be OFF.) Press the
Trigger Button [oval 50]
on the remote. The lights should
turn ON or change scene. Press the
Trigger Button [oval 50]
again and the lights should turn
OFF or change scenes.
Exit Setup
If no further programming is required, press the
AVR Button [oval 5]
on the AVR21ENR1 remote
and then the
Exit Button [oval 17]
to return to normal operation mode.
CURTAIN CONTROL
To open and close a curtain with the AVR turn on/turn off functions, press the
Menu Button [oval
44]
on the remote to bring the
MAIN MENU
to the screen. Press the
▼
/
▲
Navigation Button
[oval 16]
so that the cursor is pointed to the
REMOTE CONTROL SETUP
line. Press the
Set
Button [oval 18]
. The
REMOTE CNTL SETUP 1
screen will appear. Press the
▼
/
▲
Navigation
Button [oval 16]
so that the cursor is pointed to
GO TO REMOTE CNTL 2
. Press the
Set
Button [oval 18]
. The
REMOTE CNTL SETUP 2
screen will appear. Press the
▼
/
▲
Navigation
Button [oval 16]
so that the cursor is pointed to the
CURTAIN CONTROL
line. Press the
Set
Button [oval 18]
. The
CURTAIN CONTROL SETUP
screen will appear.
Carrier
With the cursor positioned next to
CARRIER
, press the
◄
/
►
Navigation Button [oval 16]
to
select the proper setting. NOTE: Most IR remotes used with common source components will
have a carrier, so
YES
should be selected as a first test. Some Cable Box remotes do not use a
carrier, so if a code setting doesn’t work, try changing this setting.
Summary of Contents for AVR21EN
