Audioaccess AVR21EN, Installation Instructions Manual

Page: 89 / 222

89
Invert Code
Press the ▼ / ▲ Navigation Button [oval 16] to move the cursor next to:
INVERT CODE
. Press
the ◄ / ► Navigation Button [oval 16] to select
YES/NO
. Most devices will be set to
NO
. Certain
devices, (Sony S-Link, Harman Kardon Remote Control IN) will require a YES setting. Try
changing this setting if a specific code selection does not work for a given device.
Program Code
Press the ▼ / ▲ Navigation Button [0val 16] so that the cursor is pointed to the
PREOGRAM
CODE line. Press the Set Button [oval 18] . The TV/PROJ CODE PROGRAM screen will appear.
TV/Proj Program Code (Manual)
Press the ▼ / ▲ Navigation Button [oval 16] so that the cursor is pointed to the
MANUAL
line.
Press the Set Button [oval 18] . The
TV/PROJ MANUAL PROG
screen will appear.
SOURCE
TYPE will be fixed as selected ( TV/PROJ ).
Press the ▼ / ▲ Navigation Button to move the cursor next to:
BRAND
. Press the ◄ / ►
Navigation Button [oval 16] to select the appropriate brand.
Press the
▼ / ▲ Navigation Button [oval 16] to move the cursor next to: TRY CODES . With the
AVR21ENR1 Main Room Remote pointing toward the AVR front panel, starting with 1, slowly
press the numeric buttons through the range indicated on screen, until the unit being configured
turns off. When the unit turns off, press the
▼ / ▲ Navigation Button [oval 16] to move the cursor
next to: YES . Press the Set Button [oval 18]. This will ‘save’ this code group for ON/OFF control
of the TV/Projector.
If no IR ON/OFF commands were found, see
Automatic and Learn , below.
If no further programming is required, press the
AVR Button [oval 5] on the AVR21ENR1 remote
and then the Exit Button [oval 17] to return to normal operation mode.
To continue in setup, press the
▼ Navigation Button [oval 16] to move the cursor next to:
BACK
TO T/P CODE PROG . Press the Set Button [oval 18] . Press the ▼ Navigation Button again to
move the cursor next to: BACK TO T/P CNTL SETUP . Press the Set Button [oval 18] . The
TV/PROJ CONTROL SETUP
screen will appear.
To program
SCREEN UP/DOWN
,
LIGHTING ON/OFF
,
CURTAIN OPEN/CLOSE
, press the
▼ / ▲ Navigation Button [oval 16] to move the cursor next to: BACK TO REM CNTL SETUP .
Press the Set Button [oval 18] . See the Screen and Lighting sections following.
TV/Proj Program Code (Automatic)
If ON/OFF codes could not be found by Brand in the Manual Mode, try searching by source type
in the Automatic mode.
In the
TV/PROJ CODE PROGRAM
screen, press the ▼ / ▲ Navigation Button [oval 16] to move
the cursor next to:
AUTOMATIC
. Press the Set Button [oval 18] . The
TV/PROJ AUTO PROGRAM
screen will appear.
The
SOURCE
will be fixed as selected (
TV/PROJ
). Press the ▼ Navigation Button [oval 16] to
move the cursor next to:
TRY CODES
. Repeatedly press the ◄ or ► Navigation Button [oval 16]
to test all selected device type commands until the unit turns off. When the unit turns off, press
the
▼ Navigation Button [oval 16] to move the cursor next to: YES . Press the Set Button [oval
18] to ‘save’ the code group. This will set this code group for ON/OFF control of the TV/Projector.
If no further programming is required, press the
AVR Button [oval 5] on the AVR21ENR1 remote
and then the Exit Button to return to normal operation mode.