129
Front Panel Settings
The front-panel information display will normally stay on at full brightness as long as the AVR is
ON. In some situations, such as a darkened theater room, the light from the display might be
distracting. The display can be set to fade out and turn off from 3-9 seconds after a remote or
front-panel button press. The display will illuminate full brightness when a remote or front panel
button is pressed.
To set front-panel timeout,
press the remote
Menu Button [oval 44]
to bring the
MAIN MENU
to
the screen. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
MAIN ROOM SETUP
line. Press the
Set Button [oval 18]
. Press the
▼
/
▲
Navigation Button
[oval 16]
so that the cursor is pointed to the
ADVANCED
line. Press the
Set Button [oval 18]
.
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
FRNT PANEL
TIMEOUT
line. Press the
◄
/
►
Navigation Button [oval 16]
to select the desired duration from
3s-9s
(3 seconds-9 seconds). The AVR will operate at this setting until the setting is changed in
setup. NOTE: When the display has been turned off, the green power indicator in the Power
Button will remain on to show power to the AVR.
Front Panel Brightness
The AVR21EN’s front-panel displays and indicators are set at a default brightness level that is
sufficient for viewing in a normally lit room. However, you may wish to occasionally lower the
brightness of the display, or turn it off completely.
To set front-panel brightness, press the remote
Menu Button [oval 44]
to bring the
MAIN MENU
to the screen. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
MAIN ROOM SETUP
line. Press the
Set Button [oval 18]
. Press the
▼
/
▲
Navigation Button
[oval 16]
so that the cursor is pointed to the
ADVANCED
line. Press the
Set Button [oval 18]
.
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
FRNT PNL
BRGHTNSS
line. Press the
◄
/
►
Navigation Button [oval 16]
to select
FULL
,
HALF
or
OFF
. The
AVR will operate at this setting until the power is turned OFF (standby). When the AVR is
powered up the displays and indicators will illuminate at full brightness. NOTE: When the display
has been turned off, the green power indicator in the
Standby/ON Button [square 2]
will remain
on to show power to the AVR.
Power On Volume
The AVR has two options for Main Room turn on audio level.
OFF:
With
POWER ON VOLUME
set to
OFF
, the AVR will always turn on to the volume level set
when the unit was turned OFF.
ON:
With
POWER ON VOLUME
set to
ON
, the AVR will always turn on to a preset volume. The
preset level is configured in the
POWER ON VOL LVL
line.
To set power on volume, press the remote
Menu Button [oval 44]
to bring the
MAIN MENU
to
the screen. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
MAIN ROOM SETUP
line. Press the
Set Button [oval 18]
. Press the
▼
/
▲
Navigation Button
[oval 16]
so that the cursor is pointed to the
ADVANCED
line. Press the
Set Button [oval 18]
.
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
POWER ON
VOLUME
line. Press the
◄
/
►
Navigation Button [oval 16]
to select
OFF/ON
.
If setting a Power On Volume level, press the
▼
/
▲
Navigation Button [oval 16]
to position the
cursor next to:
POWER ON VOL LVL.
Press the
◄
/
►
Navigation Button [oval 16]
to set the
desired level. Range: -50dB to -10dB. This setting will not change until changed in setup.
On Screen Status
This setting configures the duration for on-screen display of AVR front panel and remote button
presses.
Summary of Contents for AVR21EN
