182
To name Zones:
1. In
SETUP BY NUMBER PAGE 1
, press the
▼
/
▲
Navigation Button [oval 16]
to position the
cursor next to
NAME
. Press the
Set Button [oval 18]
. A white rectangle will flash to the right
of
NAME:
indicating that the remote can be used to enter the letters for the zone name.
2. Using either the
▼
/
▲
Navigation Button [oval 16]
or the
Alphanumeric Buttons [oval 46]
,
enter the first letter for the group name. (i.e. KITCHEN). When the first letter appears on
screen, press the
►
Navigation Button [oval 16]
to move the cursor to the next letter
position.
3. Repeat steps 2-3 above until the Zone Name has been spelled out. A Zone Name can have
up to 12 letters. Press the
Set Button [oval 18]
. This will store the name and return the
cursor to the arrow next to
NAME
.
4. To name additional zones, press the
▼
/
▲
Navigation Button [oval 16]
to position the
cursor next to
ZONE NUMBER
. Press the
◄
/
►
Navigation Button [oval 16]
to select another
zone.
5. Repeat steps 2-4 until all desired zones have been named.
To exit setup, press the
Exit Button [oval 17]
. To continue Zone Setup, position the cursor next
to
TYPE
and continue to the next section.
Setup Access
Setup access determines whether the keypad in a particular zone, allows access to the Keypad
Setup Menu. The Keypad Setup Menu includes the settings for ON Volume, Tone Controls, Party
Mode Turn On Volume, EQ, Backlight Configuration and Power On Mode. Given the complexity
of the system and the sophistication of the user, a decision must be made to allow or block user
access to these settings.
To Configure Setup Access:
1. In
SETUP BY NUMBER PAGE 1
, press the
▼
/
▲
Navigation Button [oval 16]
to position the
cursor next to
SETUP ACCESS
.
2. Using
the
◄
/
►
Navigation Button [oval 16]
, select access setting:
ALLOW
or
BLOCK
.
To exit setup, press the
Exit Button [oval 17]
. To continue Zone Setup, position the cursor next
to
PAGING GROUP
and continue to the next section.
Paging Group
Selecting a Group in this setting will place the zone being configured into a select group of zones
that will be paged, i.e. BEDROOMS or COMMON areas when selected in the Paging sub-menu
on the zone keypad. As described in the section “Naming Paging Groups”, the system features
default Paging to
ALL
(all zones) and
PAGE KEYPAD
(the ability to page a specific zone) so only
special groups as determined by the homeowner will need to be configured. Up to 8 Paging
Groups can be created. If a zone is not to be included in any of the special Paging Groups, select
NONE
. With none selected, the zone will still be accessible for paging in the ALL or Page Keypad
menus, unless
PAGE ROOM
has been set to:
NO
, in
SETUP BY NUMBER PAGE 2
.
To select Paging Group:
1. In
the
SETUP BY NUMBER PAGE 1
screen, press the
▼
/
▲
Navigation Button [oval 16]
to
position the cursor next to
PAGING GROUP
.
2. Using
the
◄
/
►
Navigation Button [oval 16]
, select the Paging Group for the zone being
configured: NONE, A, B, C, D, E, F, G or H.
To exit setup, press the
Exit Button [oval 17]
. To continue Zone Setup, position the cursor next
to
ENTERTAINMENT GROUP
and continue to the next section.
Entertainment Group
Selecting a Group in this setting will place the zone being configured into a select group of zones
that will be activated (if off) and switched to a common source (within the group). The zones will
Summary of Contents for AVR21EN
