ARM ARM1176JZF-S Technical Reference Manual Download Page 482 | Manualshive

Page: 482 / 759

background image

Debug

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

13-8

ID012310

Non-Confidential, Unrestricted Access

Figure 13-3 Debug Status and Control Register format

Table 13-4 lists the bit field definitions for the Debug Status and Control Register.

31 30 29 28

16 15 14 13 12 11 10

6 5

2 1 0

UNP/SBZP

rDTRfull

wDTRfull

UNP/SBZP

Monitor debug-mode enable

Mode select

Execute ARM instruction enable

9

7

8

Core restarted

Core halted

17

18

19

20

Imprecise data abort ignored

Non-Secure World status

Not Secure Privileged Non-Invasive

Debug enable,

SPNIDEN

input pin

Not Secure Privileged Invasive

Debug Enable,

SPIDEN

input pin

Method of debug entry

User mode access to DCC control

DbgAck

Interrupts disable

Sticky imprecise Data Aborts flag

Sticky Undefined flag

Power down disable

Sticky precise Data Abort flag

Table 13-4 Debug Status and Control Register bit field definitions

Bits

Core view

External
view

Reset
value

Description

[31]

UNP/SBZP

UNP/SBZP

-

Reserved.

[30]

R

R

0

The rDTRfull flag:

0 = rDTR empty

1 = rDTR full.

This flag is automatically set on writes by the DBGTAP debugger to
the rDTR and is cleared on reads by the core of the same register. No
writes to the rDTR are enabled if the rDTRfull flag is set.

[29]

R

R

0

The wDTRfull flag:

0 = wDTR empty

1 = wDTR full.

This flag is automatically cleared on reads by the DBGTAP debugger
of the wDTR and is set on writes by the core to the same register.

[28:20]

UNP/SBZP

UNP/SBZP

-

Reserved.

[19]

R

R

0

Imprecise Data Aborts Ignored. This read-only bit is set by the core in
Debug state following a Data Memory Barrier operation, and cleared
on exit from Debug state. When set, the core does not act on imprecise
data aborts. However, the sticky imprecise data abort bit is set if an
imprecise data abort occurs when in Debug state.

«
...
480
481
482
483
484
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

Brand: DBM Pages: 50

Armor 101 Series

Brand: Lochinvar Pages: 28

Armor 101 Series

Brand: Lochinvar Pages: 44

Brand: Orban Pages: 255

Aquaduct 360 XT

Brand: Aqua Computer Pages: 28

ELC-LTTR240-TBP

Brand: ENERMAX Pages: 16

Brand: NKE Pages: 15

Brand: Accusys Pages: 34

EK-FC750 GTX Series

Brand: ekwb Pages: 2

ipRocketLink IAD 3086

Brand: Patton electronics Pages: 12

Brand: CAME Pages: 32

cPCIS-1100 Series

Brand: ADLINK Technology Pages: 48

ULTRIX-FM-NS-1RU

Brand: Ross Pages: 5

Brand: MESA Electronic Pages: 27

SNMP-1000-E2B1E

Brand: Advantech Pages: 4

Brand: Omron Pages: 4

Brand: R3 Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands