ARM ARM1176JZF-S Technical Reference Manual Download Page 153 | Manualshive

Page: 153 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-21

ID012310

Non-Confidential, Unrestricted Access

To use the Main ID Register read CP15 with:

•

Opcode_1 set to 0

•

CRn set to c0

•

CRm set to c0

•

Opcode_2 set to 0.

For example:

MRC p15,0,<Rd>,c0,c0,0 ;Read Main ID Register

For more information on the processor features, see

c0, CPUID registers

on page 3-26.

3.2.3

c0, Cache Type Register

The purpose of the Cache Type Register is to provide information about the size and architecture
of the cache for the operating system. This enables the operating system to establish how to
clean the cache and how to lock it down. Inclusion of this register enables RTOS vendors to
produce future-proof versions of their operating systems.

The Cache Type Register is:

•

in CP15 c0

•

a 32-bit read only register, common to Secure and Non-secure worlds

•

accessible in privileged modes only.

All ARMv4T and later cached processors contain this register. Figure 3-11 shows the
arrangement of bits in the Cache Type Register.

Figure 3-11 Cache Type Register format

Table 3-6 lists how the bit values correspond with the Cache Type Register functions.

0

31 30 29 28

25 24 23

12 11

0

0 0

Ctype

S

P 0

Size

Assoc

M Len

P 0

Size

Assoc

M Len

Dsize

Isize

22 21

18 17

15 14 13

10 9

6 5

3 2 1

Table 3-6 Cache Type Register bit functions

Bits

Field name

Function

[31:29]

-

0

[28:25]

Ctype

The Cache type and Separate bits provide information about the cache architecture.

b1110, indicates that the ARM1176JZF-S processor supports:

•

write back cache

•

Format C cache lockdown

•

Register 7 cache cleaning operations.

[24]

S bit

S = 1, indicates that the processor has separate instruction and data caches and not a unified
cache.

«
...
151
152
153
154
155
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: ABB Pages: 66

Brand: Maco Pages: 38

LS42 - BladeCenter - 7902

Brand: IBM Pages: 56

Brand: IBM Pages: 2

BladeCenter Management Module

Brand: IBM Pages: 78

Brand: IBM Pages: 110

Remote Supervisor Adapter II

Brand: IBM Pages: 132

HiGain HLU-231 List 8F

Brand: ADC Pages: 7

Brand: EVS Pages: 30

Brand: SIIG Pages: 6

FireWire 800 + Hi-Speed USB Combo

Brand: SIIG Pages: 20

Brand: MC Pages: 21

Brand: Rajant Corporation Pages: 40

Brand: Juniper Pages: 420

Brand: uneron Pages: 13

Brand: National Instruments Pages: 52

MULTIflight Stick

Brand: Multiplex Pages: 10

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands