ARM ARM1176JZF-S Technical Reference Manual Download Page 375 | Manualshive

Page: 375 / 759

background image

Level One Memory System

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

7-4

ID012310

Non-Confidential, Unrestricted Access

Figure 7-1 Level one cache block diagram

7.2.1

Features of the cache system

The level one cache system has the following features:

•

The cache is a Harvard implementation.

•

The caches are lockable at a granularity of a cache way, using Format C lockdown. See

Cache control and configuration

on page 3-7.

•

Cache replacement policies are Pseudo-Random or Round-Robin, as controlled by the RR
bit in CP15 register c1. Round-Robin uses a single counter for all sets, that selects the way
used for replacement.

•

Cache line allocation uses the cache replacement algorithm when all cache lines are valid.
If one or more lines is invalid, then the invalid cache line with the lowest way number is
allocated to in preference to replacing a valid cache line. This mechanism does not
allocate to locked cache ways unless all cache ways are locked. See

Cache miss handling

when all ways are locked down

on page 7-6.

•

Cache lines can contain either Secure or Non-secure data and the NS Tag, that the
MicroTLB provides, indicates when the cache line comes from Secure or Non-secure
memory.

•

Cache lines can be either Write-Back or Write-Through, determined by the MicroTLB
entry.

•

Only read allocation is supported.

DATARAM

TAGRAM

TCM

Comparator

Way

select

Write buffer data (1-2 words)

Write buffer addresses

Micro

TLB

Cache

hit

Data

out

Micro TLB

miss and

Data Abort

RAMSet base address and size

CP15

interface

Virtual

address

Write

data

«
...
373
374
375
376
377
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

Brand: Palm Pages: 4

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

Through Hole Power Inductors 1411

Brand: Delta Electronics Pages: 1

Brand: ICP Pages: 68

Tamar FCSAS102800

Brand: Bridgeworks Pages: 56

HFisolator 9730/26-11

Brand: Stahl Pages: 2

Service Aggregation Router 7705

Brand: Alcatel-Lucent Pages: 20

Brand: IBM Pages: 44

Brand: Ezquest Pages: 65

Brand: Ericsson Pages: 16

Brand: 4ms Company Pages: 4

Brand: iSMA CONTROLLI Pages: 20

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands