manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Clocking and Resets 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

9-10

ID012310

Non-Confidential, Unrestricted Access

9.4

Reset modes

The reset signals present in the processor design enable you to reset different parts of the design 
independently. Table 9-1 lists the reset signals, and the combinations and possible applications 
that you can use them in.

If you do not use VFP shutdown for power saving, you can treat the 

nVFPRESETIN

 signal in 

the same way as 

nRESETIN

. For more information on power management and VFP, see 

VFP 

shutdown

 on page 10-6.

9.4.1

Power-on reset

You must apply power-on or 

cold

 reset to the processor when power is first applied to the 

system. In the case of power-on reset, the leading, falling, edge of the reset signals, 

nRESETIN

 

and 

nPORESETIN

, does not have to be synchronous to 

CLKIN

. Because the 

nRESETIN

 and 

nPORESETIN

 signals are synchronized within the processor, you do not have to synchronize 

these signals. Figure 9-6 shows the application of power-on reset.

Figure 9-6 Power-on reset

It is recommended that you assert the reset signals for at least three 

CLKIN

 cycles to ensure 

correct reset behavior. Adopting a three-cycle reset eases the integration of other ARM parts into 
the system, for example, ARM9TDMI-based designs.

It is not necessary to assert 

DBGnTRST

 on power-up.

9.4.2

CP14 debug logic

Because the 

nPORESETIN

 signal is synchronized within the processor, you do not have to 

synchronize this signal.

Table 9-1 Reset modes

Reset mode

nRESETIN

DBGnTRST

nPORESETIN

Application

Power-on reset

0

x

0

Reset at power up, full system reset. 
Hard reset or cold reset.

Processor reset

0

x

1

Reset of processor core only, watchdog 
reset.

Soft reset or warm reset.

DBGTAP reset

1

0

1

Reset of DBGTAP logic.

Normal

1

x

1

No reset. Normal run mode.

CLKIN

nRESETIN

nPORESETIN

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
Measurement Computing PC-CARD DAS16 User Manual preview
PC-CARD DAS16
Brand: Measurement Computing Pages: 27
Omega OMB-DAQBOARD-3000 Series User Manual preview
OMB-DAQBOARD-3000 Series
Brand: Omega Pages: 108
Altera DE2-70 User Manual preview
DE2-70
Brand: Altera Pages: 93
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Brand: ADTRAN Pages: 46
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Brand: Moxa Technologies Pages: 2
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Brand: ICP DAS USA Pages: 62
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Brand: ZALMAN Pages: 7
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Brand: Advantech Pages: 96
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Brand: ATI Technologies Pages: 20
Rainbow QPBB Instruction Manual preview
QPBB
Brand: Rainbow Pages: 2
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Brand: Intercoax Pages: 2
Xyclop XC-4CH-NVR-1TB User Manual preview
XC-4CH-NVR-1TB
Brand: Xyclop Pages: 144
Silvertel Ag102 User Manual preview
Ag102
Brand: Silvertel Pages: 9
Corsair Hydro H110 Quick Start Manual preview
Hydro H110
Brand: Corsair Pages: 10

Brands by name

Popular brands

Load more brands