ARM ARM1176JZF-S Technical Reference Manual Download Page 143 | Manualshive

Page: 143 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-11

ID012310

Non-Confidential, Unrestricted Access

•

interrupts

•

fast interrupts

•

external debug requests.

The system validation registers consist of four 32-bit read/write registers. Figure 3-8 shows the
arrangement of registers.

Figure 3-8 System validation registers

The System Validation Counter Register and System Validation Operations Register reuse the
Cycle Counter Register, Count Register 0, and Count Register 1, see

System performance

monitor

on page 3-10, to schedule resets, interrupts and fast interrupts respectively. External

debug requests are scheduled using an additional 6 bit counter that is not used by the System
performance monitor registers.

Each of the four counters counts upwards, and when the counter overflows, the corresponding
event occurs. To the core, the events are indistinguishable from ordinary external events. The
System Validation Registers provide functions for loading the counter registers with the
required number of clock cycles before the event occurs, and starting, stopping and clearing the
counters, to return them to their System performance monitor functionality.

The System Validation Registers are usually only accessible from Secure privileged modes, but
a Secure User and Non-secure Access Validation Control Register is provided to permit access
to the System Validation Registers from User modes and Non-secure modes.

The System Validation Cache Size Mask Register masks the physical size of the caches and
TCMs to make their size appear different to the processor. You can use this in validation by
simulation, but you must not use it in a manufactured device because it can corrupt correct
operation of the processor.

Read-only

Read/write

c12

4

c13

c15

Write-only

Secure User and Non-secure Access Validation Control Register

System Validation
Counter Registers

System
Validation
Operations
Registers

0

c9

0

Opcode_2

Opcode_1

CRm

CRn

System Validation Cache Size Mask Register

5

6

7

Reset counter

Interrupt counter

Fast interrupt counter

External debug request counter

0

c13

1

c13

2

c13

3

2

3

4

5

1

6

7

2

3

4

5

1

6

7

Start reset counter

Start interrupt counter

Start reset and interrupt counters

Start fast interrupt counter

Start reset and fast interrupt counters

Start interrupt and fast interrupt counters

Start reset, interrupt and fast interrupt counters

Start external debug request counter

Stop reset counter

Stop interrupt counter

Stop reset and interrupt counters

Stop fast interrupt counter

Stop reset and fast interrupt counters

Stop interrupt and fast interrupt counters

Stop reset, interrupt and fast interrupt counters

Stop external debug request counter

Accessible in User mode

c14

0

«
...
141
142
143
144
145
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: Data Translation Pages: 60

Brand: Black Box Pages: 9

Avenue Express Control Panel

Brand: Ensemble Designs Pages: 19

Brand: Lanner electronics Pages: 59

Brand: Z3 Technology Pages: 67

RanaSystems 13-0010--001

Brand: RANA Systems Pages: 328

Brand: SYNTEK Pages: 41

PowerBeam PBE-5AC-400-ISO

Brand: Ubiquiti Pages: 23

Brand: Rajant Corporation Pages: 40

EK-FC750 GTX Series

Brand: ekwb Pages: 2

Brand: Meinberg Pages: 14

HiGain Line Unit HLU-388

Brand: PairGain Pages: 7

Brand: Intel Pages: 51

Brand: Juniper Pages: 30

Brand: HYCON Pages: 13

Brand: Siklu Pages: 52

Brand: Airaya Pages: 28

CNPS7000B Series

Brand: ZALMAN Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands