ARM ARM1176JZF-S Technical Reference Manual Download Page 28

Page: 28 / 759

Introduction

ARM DDI 0301H

1-2

ID012310

Non-Confidential, Unrestricted Access

1.1

About the processor

The ARM1176JZF-S processor incorporates an integer core that implements the ARM11 ARM
architecture v6. It supports the ARM and Thumb

™

instruction sets, Jazelle technology to enable

direct execution of Java bytecodes, and a range of SIMD DSP instructions that operate on 16-bit
or 8-bit data values in 32-bit registers.

The ARM1176JZF-S processor features:

•

TrustZone

™

security extensions

•

provision for

Intelligent Energy Management

(IEM

™

)

•

high-speed

Advanced Microprocessor Bus Architecture

(AMBA)

Advanced Extensible

Interface

(AXI) level two interfaces supporting prioritized multiprocessor

implementations.

•

an integer core with integral EmbeddedICE-RT logic

•

an eight-stage pipeline

•

branch prediction with return stack

•

low interrupt latency configuration

•

internal coprocessors CP14 and CP15

•

Vector Floating-Point

(VFP) coprocessor support

•

external coprocessor interface

•

Instruction and Data

Memory Management Units

(MMUs), managed using MicroTLB

structures backed by a unified Main TLB

•

Instruction and data caches, including a non-blocking data cache with

Hit-Under-Miss

(HUM)

•

virtually indexed and physically addressed caches

•

64-bit interface to both caches

•

level one

Tightly-Coupled Memory

(TCM) that you can use as a local RAM with DMA

•

trace support

•

JTAG-based debug.

Note

The only functional difference between the ARM1176JZ-S and ARM1176JZF-S processor is
that the ARM1176JZF-S processor includes a

Vector Floating-Point

(VFP) coprocessor.

Summary of Contents for ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands

ARM ARM1176JZF-S, Technical Reference Manual

Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands