manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Trace Interface Port 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

15-5

ID012310

Non-Confidential, Unrestricted Access

Table 15-5 lists the 

ETMDACTL[17:0]

 signals.

15.1.4

Data value interface

The data values are sampled at the WBls stage. Here the load, store, MCR, and MRC data is 
combined. The memory view of the data is presented, and must be converted back to the register 
view depending on the alignment and endianness.

Data is not returned for at least two cycles after the address. However, it is not necessary to 
pipeline the address because the slot does not return data for a previous address during this time. 
Data values are defined to correspond to the most recent data addresses with the same slot 
number, starting from the previous cycle. In other words, data can correspond to an address from 
the previous cycle, but not to an address from the same cycle.

Table 15-5 ETMDACTL[17:0]

Bits

Reference name

Description

Qualified by

[17]

DANSeq

The data transfer is nonsequential from the last. This signal must be 
asserted on the first cycle of each instruction, in addition to the second 
transfer of a SWP or LDM pc, because the address of these transfers 
is not one word greater than the previous transfer, and therefore the 
transfer must have its address re-output.

During an unaligned access, this signal is only valid on the first 
transfer of the access.

DASlot

!= 00

[16]

DALast

The data transfer is the last for this data instruction. This signal is 
asserted for both halves of an unaligned access.

A related signal, DAFirst, can be implied from this signal, because the 
next transfer must be the first transfer of the next data instruction.

DASlot

!= 00

[15]

DACPRT

The data transfer is a CPRT.

DASlot

!= 00

[14]

DASwizzle

Words must be byte swizzled for ARM big-endian mode. During an 
unaligned access, this signal is only valid on the first transfer of the 
access.

DASlot

!= 00

[13:12]

DARot

Number of bytes to rotate right each word by. During an unaligned 
access, this signal is only valid on the first transfer of the access.

DASlot

!= 00

[11]

DAUnaligned

First transfer of an unaligned access.

The next transfer must be the second half, where this signal is not 
asserted.

DASlot

!= 00

[10:3]

DABLSel

Byte lane selects.

DASlot

!= 00

[2]

DAWrite

Read or write.

During an unaligned access, this signal is only valid on the first 
transfer of the access.

DASlot

!= 00

[1:0]

DASlot

Slot occupied by data item.

b00 indicates that no slot is in use in this cycle.

b11 indicates that ETM is in use in this cycle.

This slot holds the value even when the ETM is powered down.

None

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

CAME QBEMFSB2 User Manual preview
QBEMFSB2
Brand: CAME Pages: 19
Amperes iPX5500 Instruction Manual preview
iPX5500
Brand: Amperes Pages: 8
Avaya PARTNER PC CARD Installation Instructions preview
PARTNER PC CARD
Brand: Avaya Pages: 4
Dataprobe iBoot-Exp Manual preview
iBoot-Exp
Brand: Dataprobe Pages: 5
KonNad SinoCon C2000-C2-SHK0401-BB1 User Manual preview
SinoCon C2000-C2-SHK0401-BB1
Brand: KonNad Pages: 12
Kontron CP3002-RA User Manual preview
CP3002-RA
Brand: Kontron Pages: 98
Renesas REJ06B0734-0100 Application Note preview
REJ06B0734-0100
Brand: Renesas Pages: 19
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Brand: ebm-papst Pages: 13
Icy Box IB-NAS5520 Quick Start Manual preview
IB-NAS5520
Brand: Icy Box Pages: 2
Intel G6950 Documentation Update preview
G6950
Brand: Intel Pages: 51
Alpine PXE-R600 Manual preview
PXE-R600
Brand: Alpine Pages: 17
Abov A34M418YLN User Manual preview
A34M418YLN
Brand: Abov Pages: 8
Acnodes RK 1016B User Manual preview
RK 1016B
Brand: Acnodes Pages: 10
Panasonic KX-W1000 Service Manual preview
KX-W1000
Brand: Panasonic Pages: 78
IBASE Technology ET880 Series User Manual preview
ET880 Series
Brand: IBASE Technology Pages: 64
Baracoda BLUETOOTH RS232RS232 User Manual preview
BLUETOOTH RS232RS232
Brand: Baracoda Pages: 21
Dell PowerEdge 2650 Service Manual preview
PowerEdge 2650
Brand: Dell Pages: 65
Extron electronics SMP 351 User Manual preview
SMP 351
Brand: Extron electronics Pages: 220

Brands by name

Popular brands

Load more brands