ARM ARM1176JZF-S Technical Reference Manual Download Page 685 | Manualshive

Page: 685 / 759

background image

VFP Exception Handling

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

22-2

ID012310

Non-Confidential, Unrestricted Access

22.1

About exception processing

The VFP11 coprocessor handles exceptions, other than inexact exceptions, imprecisely with
respect to both the state of the ARM11 processor and the state of the VFP11 coprocessor. It
detects an exceptional instruction after the instruction passes the point for exception handling in
the ARM11 processor. It then enters the

exceptional state

and signals the presence of an

exception by refusing to accept a subsequent VFP instruction. The instruction that triggers
exception handling bounces to the ARM11 processor. The bounced instruction is not necessarily
the instruction immediately following the exceptional instruction. Depending on sequence of
instructions that follow, the bounce can occur several instructions later.

The VFP11 coprocessor can generate exceptions only on arithmetic operations. Data transfer
operations between the ARM11 processor and the VFP11 coprocessor, and instructions that
copy data between VFP11 registers, FCPY, FABS, and FNEG, cannot produce exceptions.

In full-compliance mode the VFP11 hardware and support code together process exceptions
according to the IEEE 754 standard. VFP11 exception processing includes calling user trap
handlers with intermediate operands specified by the IEEE 754 standard. In RunFast mode, the
VFP11 coprocessor generates the default, or trap disabled, value when an overflow, invalid
operation, division by zero, or inexact condition occurs. RunFast mode does not provide for user
trap handlers.

For descriptions of each of the exception flags and their bounce characteristics, see the sections

Input Subnormal exception

on page 22-12 to

Arithmetic exceptions

on page 22-20.

«
...
683
684
685
686
687
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: SAF Pages: 30

Brand: XESS Pages: 23

Brand: Paradyne Pages: 85

Brand: hilscher Pages: 154

Brand: ZALMAN Pages: 11

Brand: Hauppauge Pages: 55

Brand: Supero Pages: 53

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Brand: Uctronics Pages: 2

Brand: LST Pages: 1

Brand: Lanner Pages: 141

Brand: El.Mo Pages: 16

Brand: Zhone Pages: 494

Brand: IEI Technology Pages: 213

Brand: AMX Pages: 1

Brand: Sony Pages: 8

Brand: Sony Pages: 14

Brand: Sony Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands