manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

System Control Coprocessor 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-89

ID012310

Non-Confidential, Unrestricted Access

To use the Instruction and Data Cache Lockdown Registers read or write CP15 with:

•

Opcode_1 set to 0

•

CRn set to c9

•

CRm set to c0

•

Opcode_2 set to:

—

0, for Data Cache

—

1, for Instruction Cache.

For example:

MRC p15, 0, <Rd>, c9, c0, 0

; Read Data Cache Lockdown Register

MCR p15, 0, <Rd>, c9, c0, 0

; Write Data Cache Lockdown Register

MRC p15, 0, <Rd>, c9, c0, 1

; Read Instruction Cache Lockdown Register

MCR p15, 0, <Rd>, c9, c0, 1

; Write Instruction Cache Lockdown Register

The system must only change a cache lockdown register when it is certain that all outstanding 
accesses that might cause a cache line fill are complete. For this reason, the processor must 
perform a Data Synchronization Barrier operation before the cache lockdown register changes, 
see 

Data Synchronization Barrier operation

 on page 3-83.

The following procedure for lock down into a data or instruction cache way i, with N cache 
ways, using Format C, ensures that only the target cache way i is locked down.

This is the architecturally defined method for locking data or instructions into caches:

1.

Ensure that no processor exceptions can occur during the execution of this procedure, by 
disabling interrupts. If this is not possible, all code and data or instructions used by any 
exception handlers that can be called must meet the conditions specified in step 2.

2.

Ensure that all data or instructions used by the following code, apart from the data or 
instructions that are to be locked down, are either:

•

in an noncacheable area of memory, including the TCM

•

in an already locked cache way.

3.

Ensure that the data or instructions to be locked down are in a Cacheable area of memory.

4.

Ensure that the data or instructions to be locked down are not already in the cache, using 
cache Clean and/or Invalidate instructions as appropriate, see 

c7, Cache operations

 on 

page 3-69.

5.

Enable allocation to the target cache way by writing to the Instruction or Data Cache 
Lockdown Register, with the CRm field set to 0, setting L equal to 0 for bit i and L equal 
to 1 for all other ways.

6.

Ensure that the memory cache line is loaded into the cache by using an LDR instruction 
to load a word from the memory cache line, for each of the cache lines to be locked down 
in cache way i.

To lock down an instruction cache use the c7 Prefetch Instruction Cache Line operation 
to fetch the memory cache line, see 

Invalidate, Clean, and Prefetch operations

 on 

page 3-71.

7.

Write to the Instruction or Data Cache Lockdown Register, setting L to 1 for bit i and 
restore all the other bits to the values they had before this routine was started.

3.2.25

c9, Data TCM Region Register

The purpose of the Data TCM Region Register is to describe the physical base address and size 
of the Data TCM region and to provide a mechanism to enable it.

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
NXP Semiconductors TWR-SB0410-36EVB User Manual preview
TWR-SB0410-36EVB
Brand: NXP Semiconductors Pages: 26
BSS Audio EC-4B Installation Manual preview
EC-4B
Brand: BSS Audio Pages: 20
Reeven NAIA Installation Manual preview
NAIA
Brand: Reeven Pages: 2
Barco ImagePRO-HD Installation Manual preview
ImagePRO-HD
Brand: Barco Pages: 121
ZALMAN CNPS12X User Manual preview
CNPS12X
Brand: ZALMAN Pages: 11
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
H3C NIC-FC730i-Mb-2-32G Manual preview
NIC-FC730i-Mb-2-32G
Brand: H3C Pages: 37
IDT Tsi310TM User Manual preview
Tsi310TM
Brand: IDT Pages: 207
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
Bitspower BPTA-CPUMS-V2-SKA Instruction Manual preview
BPTA-CPUMS-V2-SKA
Brand: Bitspower Pages: 6
Lattice Semiconductor iCE40 SPRAM Series Technical Note preview
iCE40 SPRAM Series
Brand: Lattice Semiconductor Pages: 12
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Brand: Boss Pages: 20
ACTi LPR-100 Quick Installation Manual preview
LPR-100
Brand: ACTi Pages: 14
IBM 2740-1 System Reference Manual preview
2740-1
Brand: IBM Pages: 64
Advantech PPC-3211W User Manual preview
PPC-3211W
Brand: Advantech Pages: 66
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18

Brands by name

Popular brands

Load more brands