ARM ARM1176JZF-S Technical Reference Manual Download Page 639 | Manualshive

Page: 639 / 759

background image

The VFP Register File

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

19-11

ID012310

Non-Confidential, Unrestricted Access

; 2nd bank

19.7.2

Operations using register banks

The register file organization supports four types of operations that the following sections
describe:

•

Scalar-only instructions

•

Short vector-only instructions

•

Short vector instructions with scalar source

on page 19-12

•

Scalar instructions in short vector mode

on page 19-12.

See

Floating-Point Status and Control Register, FPSCR

on page 20-14 for details of the LEN

and STRIDE fields and the FPSCR register.

Scalar-only instructions

An instruction is a scalar-only operation if the operands are treated as scalars and the result is a
scalar.

Clearing the LEN field in the FPSCR register selects a vector length of one iteration. For
example, if the LEN field contains b000, then the following operation writes the sum of the
single-precision values in S21 and S22 to S12:

FADDS S12, S21, S22

Some instructions can operate only on scalar data regardless of the value in the LEN field. These
instructions are:

Compare operations

FCMPS/D, FCMPZS/D, FCMPES/D, and FCMPEZS/D.

Integer conversions

FTOUIS/D, FTOUIZS/D, FTOSIS/D, FTOSIZS/D, FUITOS/D, and FSITOS/D.

Precision conversions

FCVTDS and FCVTSD.

Short vector-only instructions

Vector-only instructions require that the value in the LEN field is nonzero, and that the
destination and Fm registers are not in bank 0.

Example 19-2 shows the iterations of the following short vector instruction:

FMACS S16, S0, S8

In the example, the LEN field contains b011, selecting a vector length of four iterations, and the
STRIDE field contains b00, selecting a vector stride of one.

Example 19-2 Short vector instruction

FMACS S16, S0, S8

; 1st iteration

FMACS S17, S1, S9

; 2nd iteration

FMACS S18, S2, S10

; 3rd iteration

FMACS S19, S3, S11

; 4th and last iteration

«
...
637
638
639
640
641
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

Brand: Omnia Pages: 102

Brand: Observint Pages: 117

Brand: Opengear Pages: 2

XM24 Expansion Module

Brand: Avaya Pages: 5

Brand: ZALMAN Pages: 11

Oresund EFC102200

Brand: Bridgeworks Pages: 84

D-NVR4108HS-4KS2/L

Brand: Dahua Pages: 33

Brand: Medel Pages: 28

Brand: Omron Pages: 6

Brand: Atmel Pages: 2

Brand: Rolls Pages: 1

PFC Chokes PFC3515V Series

Brand: Delta Electronics Pages: 1

NetVanta Analog Modem Dial Backup Interface Module

Brand: ADTRAN Pages: 2

COM Express conga-TC87

Brand: Congatec Pages: 114

Brand: Cowlacious Designs Pages: 8

Brand: DayTronic Pages: 13

BreezeNET DS.11 Configuration Utility

Brand: Alvarion Pages: 2

com.tom INDUSTRY 100.WLAN.W

Brand: Beck Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands