ARM ARM1176JZF-S Technical Reference Manual Download Page 167 | Manualshive

Page: 167 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-35

ID012310

Non-Confidential, Unrestricted Access

Table 3-25 lists the results of attempted access for each mode.

To use the Memory Model Feature Register 2 read CP15 with:

•

Opcode_1 set to 0

•

CRn set to c0

•

CRm set to c1

•

Opcode_2 set to 6.

For example:

MRC p15, 0, <Rd>, c0, c1, 6 ;Read Memory Model Feature Register 2.

c0, Memory Model Feature Register 3

The purpose of the Memory Model Feature Register 3 is to provide information about the
memory model, memory management, cache support, and TLB operations of the processor.

The Memory Model Feature Register 3 is:

•

in CP15 c0

•

a 32-bit read-only register common to the Secure and Non-secure worlds

•

accessible in privileged modes only.

Figure 3-20 shows the bit arrangement for Memory Model Feature Register 3.

Figure 3-20 Memory Model Feature Register 3 format

Table 3-26 lists how the bit values correspond with the Memory Model Feature Register 3
functions.

Table 3-25 Results of access to the Memory Model Feature Register 2

Secure Privileged

Non-secure Privileged

User

Read

Write

Read

Write

Data

Undefined exception

Data

Undefined exception

Undefined exception

Reserved

Reserved

Reserved

Reserved

Reserved

-

-

Reserved

31

8 7

4 3

0

16 15

12 11

28 27

24 23

20 19

Table 3-26 Memory Model Feature Register 3 bit functions

Bits

Field name

Function

[31:8]

-

Reserved. RAZ.

[7:4]

-

Support for hierarchical cache maintenance by MVA, all architectures

0x0

, no support in ARM1176JZF-S processors.

[3:0]

-

Support for hierarchical cache maintenance by Set/Way, all architectures.

0x0

, no support in ARM1176JZF-S processors.

«
...
165
166
167
168
169
...
»

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

IntelliJack NJ200

Brand: 3Com Pages: 4

Brand: Sangoma Pages: 6

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

Brand: Idis Pages: 86

Brand: Paradyne Pages: 2

Brand: LORD Pages: 9

Brand: Ruckus Wireless Pages: 56

Brand: Renesas Pages: 6

Brand: ADS Technologies Pages: 1

Brand: ETAS Pages: 82

Brand: Accusys Pages: 34

Brand: Lindy Pages: 12

Brand: Aleratec Pages: 16

Brand: Juniper Pages: 30

Brand: VANTAS Pages: 30

Brand: Paradyne Pages: 28

TV@nywhere Satellite

Brand: MSI Pages: 2

Brand: MSI Pages: 182

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands