manualshive.com logo in svg

ARM ARM1176JZF-S, Technical Reference Manual

The ARM ARM1176JZF-S Technical Reference Manual is a comprehensive user manual for the ARM1176JZF-S processor. Download this manual for free from manualshive.com, to gain valuable insights into the product's technical specifications, performance, and programming details. Enhance your understanding of this advanced processor with this detailed manual.

Share
Download
background image

Cycle Timings and Interlock Behavior 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

16-18

ID012310

Non-Confidential, Unrestricted Access

16.10.1 Base register update

The base register update for load or store instructions occurs in the ALU pipeline. To prevent an 
interlock for back-to-back load or store instructions reusing the same base register, there is a 
local forwarding path to recycle the updated base register around the ADD stage.

For example, the following instruction sequence take three cycles to execute:

LDR R5, [R2, #4]!
LDR R6, [R2, #0x10]!
LDR R7, [R2, #0x20]!

LDR <Rd>, [<Rn>, -<Rm>] (!)

<Rm>

If negative register offset, or shift other than LSL #2 then 
two-issue cycles.

LDR <Rd>, [Rm, -<Rm> <shf> <cns>] (!)

<Rm>

LDR <Rd>, [<Rn>], -<Rm>

<Rm>

LDR <Rd>, [<Rn>], -<Rm> <shf> <cns>

<Rm>

Table 16-15 <addr_md_1cycle> and <addr_md_2cycle> LDR example instruction explanation  (continued)

Example instruction

Early Reg

Comment

Summary of Contents for ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ARM1176JZF-S

M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
Garmin GND 10 Installation Instructions preview
GND 10
Brand: Garmin Pages: 2
IBM 3101 Maintenance Information preview
3101
Brand: IBM Pages: 63
Edge-Core SDW100 Quick Start Manual preview
SDW100
Brand: Edge-Core Pages: 7
FOR-A USF-105AS Operation Manual preview
USF-105AS
Brand: FOR-A Pages: 39
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
Avaya PARTNER PC CARD Installation Instructions preview
PARTNER PC CARD
Brand: Avaya Pages: 4
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Brand: IFM Electronic Pages: 14
Disc Makers Reflex10 User Manual preview
Reflex10
Brand: Disc Makers Pages: 38
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
IEI Technology PE-6S-R40 User Manual preview
PE-6S-R40
Brand: IEI Technology Pages: 4
ZALMAN CNPS20X User Manual preview
CNPS20X
Brand: ZALMAN Pages: 20
Extreme Networks ExtremeCloud Appliance E1120 User Manual preview
ExtremeCloud Appliance E1120
Brand: Extreme Networks Pages: 219

Brands by name

Popular brands

Load more brands