ARM ARM1176JZF-S Technical Reference Manual Download Page 156

Page: 156 / 759

System Control Coprocessor

ARM DDI 0301H

3-24

ID012310

Non-Confidential, Unrestricted Access

3.2.4

c0, TCM Status Register

The purpose of the TCM Status Register is to inform the system about the number of Instruction
and Data TCMs available in the processor.

Table 3-9 lists the purposes of the individual bits in the TCM Status Register.

Note

In the ARM1176JZF-S processor there is a maximum of two Instruction TCMs and two Data
TCMs.

The TCM Status Register is:

•

in CP15 c0

•

a 32-bit read-only register common to Secure and Non-secure worlds

•

accessible in privileged modes only.

Figure 3-12 shows the bit arrangement for the TCM Status Register.

Figure 3-12 TCM Status Register format

Table 3-9 lists how the bit values correspond with the TCM Status Register functions.

Attempts to write the TCM Status Register or read it in User modes result in Undefined
exceptions.

To use the TCM Status Register read CP15 with:

•

Opcode_1 set to 0

•

CRn set to c0

•

CRm set to c0

•

Opcode_2 set to 2.

31 30 29 28

19 18

16 15

3 2

0 0

SBZ/UNP

DTCM

SBZ/UNP

ITCM

Table 3-9 TCM Status Register bit functions

Bits

Field name

Function

[31:29]

Always b000.

[28:19]

UNP/SBZ

[18:16]

DTCM

Indicates the number of Data TCM banks implemented.

b000 = 0 Data TCMs

b001 = 1 Data TCM

b010 = 2 Data TCMs

All other values reserved

[15:3]

UNP/SBZ

[2:0]

ITCM

Indicates the number of Instruction TCM banks implemented.

b000 = 0 Instruction TCMs

b001 = 1 Instruction TCM

b010 = 2 Instruction TCMs

All other values reserved

Summary of Contents for ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands

ARM ARM1176JZF-S, Technical Reference Manual

Search results

Summary of Contents for ARM1176JZF-S

Reviews:

Related manuals for ARM1176JZF-S

Brands by name

Popular brands